Search:

Does anyone know what was the main issue some people had with this saw related to the blade guides?

Thanks for the comments. I do think it is a good deal. I know the guy and he barely used it and takes care of all his tools. The hesitation is because I have a fine 14 inch that does everything I...

I found a Delta 18" band saw model 28-682 for $300. I seems in very good condition being setup for several years. Used very little. When I look for experiences on the internet it is mixed with most...

I am looking at purchasing a set of chisels most to do basic work, not a lot of mortising. My question is about the handle designs. Some have a rounded wood design which I assume is better to par...

I have a V3000 for about 2 years now. I have great success with it.
I used 6 inch S&D pipe with pvc reducers to 4 inch S&D thin wall pipe. This thin wall pipe accept my flexible 4 inch hose but...

I would recommend a nice workbench. You can even do as I did and build one following Chris Shwartz' s book. I also just got a pin nailer and am very pleased with it.

Thanks so much for all the responses. The motor was turning very slow, grunting, and then the breaker would trip. I thought it was the starting capacitor but I swapped one from another motor and no...

My air compressor motor failed at just over 5 years old. It is a 1.75hp (about 15a) 120/240v 3450 rpm motor. Who do you buy replacement motors from? Does anyone have any experience with Harbor...

Thanks to everyone for all the responses. I have decided to go with the leg vise with the LV screw. Now to the bench building.

I am wrestling with which front vise to use on my workbench (not yet built). I am leaning towards the leg vise as it is less expensive and seems to do edge planning really well. The twin screw...

I struggled with my cyclone selection also. I ended up with the Oneida V3000. Oneida is a great company to deal with. They evaluated my shop sizing, tool dust collection needs, and tool layout. They...

Matt
It is not specific - whole range of fittings for setup. Thanks for the offer.


Thanks to all who responded. This makes me feel very comfortable with them as a supplier.

Can anyone share purchasing experiences on dust collection stuff from Ken Craft Company? Good or no so good.
The pricing is attractive.

I am not going to doing anything against code.
A friend told me that he has a PVC pipe suppling gas to his house. It is a house build about 25 yrs ago. I was wondering if was code legal at some...

Does anyone know if PVC is allowed for underground natural lines? I think it has been used in the past but may have been removed from building codes recently.

David
I agree that the G0572 seems like a good deal but I wish there were more options for the pre-filter (non Grizzly supply).

I have a DIY filter made from a HVAC blower but it blows pretty...

Matt
Are you speaking of sources other than PSI? If so, can you list them?

I noticed that filter size being 14.5 x 19 which seems to make the normally available (14x20) not an option.

Thanks...

Does anyone have experience with the Grizzly G0572 1044cfm, 3-speed air filtration unit?

It appears to have the same or similar specs to the Jet 1000b at less cost. I seemed to have read somewhere...

Guys - thanks for all the dialog. I decided to go with Oneida V series and work on upgrading my ductwork.

Thanks to all your responses. You cleared up alot of things for me.

The tables for static pressure losses show that a 45deg elbow is half the loss of a 90deg elbow. If that is the case, then using 2 45's with a short straight section to lengthen out a 90deg turn...

Who has the best pricing for pvc and/or metal pipe for dust collection?

David
I have to agree with you that comparing their data is fruitless. It would have to be done independently.

This process is driving me a little crazy -- too much data.

I think I have to go...

Paul
Which Oneida model do you have?
Thanks
Don

Matt
I don't know how old your system is but I think from reading Grizzly technical bulletin on cyclones they have made some real improvements. Looking at their fan curves the 3hp beat Oneida V3000...