Search:

Type: Posts; User: Daniel Shnitka; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    8,039

    Why even plane the all wood. Are you going to use...

    Why even plane the all wood. Are you going to use 4-5000 board feet on a project now. A experienced wood worker advised to dress/plane/cut the wood you need for your current project not the one in...
  2. ICS=Industrial Cabinet Saw, LIS=Life is short,...

    ICS=Industrial Cabinet Saw, LIS=Life is short, POO=Pride of Ownership
  3. Thank you all for the good response and the the...

    Thank you all for the good response and the the advice on drill bit speeds relative to their size and the material being bored.
    I will go back to the drill pressand see what can be done.
    I will go...
  4. Delta 20-950 Variable Speed Drill Press - bogging down

    The problem with the Delta 20-950 variable speed began with the cutting of some oak 8/4 with a 5 and 1/2 inch hole saw. The hole saw would start to cut smoothly then start to slow down as it began to...
  5. My experience and it is limited thank goodness is...

    My experience and it is limited thank goodness is you may not have to buy a new blade. The Sawstop brake is aluminum and as such I carefully removed the blade from the brake. I then took it to the...
  6. Replies
    12
    Views
    1,668

    Keep the mother of pearl. For the purist it makes...

    Keep the mother of pearl. For the purist it makes no difference to how it cuts. In the display case it will stand out as uniquely special.
  7. Replies
    72
    Views
    11,128

    I have the been more than pleased with the...

    I have the been more than pleased with the Industrial model. Every was dead accurate on set up. The correct number of nuts, bolts, washer and big clear well written explaination of how and where they...
  8. Have any of you considered Big Brothers? In...

    Have any of you considered Big Brothers? In Canada there is such an oganization that looks for responsible types to be a "big brothers" to a children one at a time. The organization are needing a...
  9. Show case the figured cherry wood with a hall...

    Show case the figured cherry wood with a hall table. Use the cherry for the drawer front and table top all framed in ash. The contrast of the light ash and it natural straight grain will have the...
  10. Replies
    29
    Views
    18,960

    Checked my fence face on the industrial cabinet...

    Checked my fence face on the industrial cabinet saw. No gap along the entire length.We are talking less than a ten thousandths of an inch.
    Sawstrop customer service as good as it gets. Returned...
  11. Replies
    27
    Views
    5,312

    I have had Sawstop Industrial model for well over...

    I have had Sawstop Industrial model for well over a year or has it been two. In all aspects it has exceeded my expectations in all categories.
  12. Replies
    1
    Views
    3,593

    Ahconite AM HONE CO. OLEAN. NY

    I was in an old second hand store, no I'll correct that first statement. I was in a junk store and i am being kind. While spending time trading wood working stories with the new but aging owner and...
  13. Highland Pattern makers vise $329.00 US dollars

    Would anyone care to comment on this vise and is anyone using such a vise? If so are you happy with having it or has it been a disappointment?
  14. Replies
    9
    Views
    1,385

    Framable picture.

    Framable picture.
  15. Nordic tablesaw blade? A brag/gloat but of minor signicance.

    I have heard and read about different table saw blades but this used but not abused saw blade was I believe a real find, a Nordic 80 tooth for clean cuts (finished edge) on laminate. I'll use it for...
  16. Replies
    1
    Views
    1,412

    Paramount Infared Patio Heater-junk!

    This has to be the most disapointing shop item I have purchased. The infared bulb last 40-50 hours. If the bulb does not burn out the wiring shorts or burns out near the bulb contact. Replacement...
  17. Jim, That sounds like the ticket, spray paint...

    Jim,
    That sounds like the ticket, spray paint and rub out, perhaps followed by a clear coat . Thanks all for your comments.
    Daniel
  18. Engraving on Stanely planes by previous owner

    I bought a couple of Stanely bench planes from a chap who was clearing out his recently deceased fathers small collection of tools. No rust and both having the appearance of very little or no use on...
  19. Replies
    5
    Views
    1,388

    I would recommend you store the router bits in...

    I would recommend you store the router bits in plastic support sleeves (see Lee Valley) that you could then insert into your block of wood. From experience I had router bits stored in a block wood (...
  20. Long shaft (30 cm) screw driver with 5/32 hex head?

    A long shaft (30 cm nearly 12 inches in length) with 5/32 Allen hex head screw driver is needed to to speed above the table router bit changes.

    I have had no luck in my search on the internet or...
  21. Replies
    48
    Views
    7,151

    I believe the company behind the cumputer...

    I believe the company behind the cumputer tecknology is the same contractor to NASA. The unit is sealed for dust and moisture.

    It is interesting that you open youir original post in a similar...
  22. Has happened, with fingers or wet wood. Watching...

    Has happened, with fingers or wet wood. Watching the video shows no material being pulled or jammed into the table saw plate insert zero clearance or otherwise.
  23. Replies
    3
    Views
    1,806

    High marks for the organization of his shop and...

    High marks for the organization of his shop and the fact he applies his theory to his practice, he walks the talk. I like his ideas and that he took the time to share them.
  24. Replies
    26
    Views
    12,196

    I have the Sawstop Industrial Cabinet Saw. In...

    I have the Sawstop Industrial Cabinet Saw. In every measurable category excluding the the braking system it comes out ahead.
    I started researching the table saws nearly four years ago. After many...
  25. Replies
    44
    Views
    5,932

    Mr. Dolan, I agree with you. Successful...

    Mr. Dolan,
    I agree with you.
    Successful companies keep their customers.

    1. The customer may not be right, but the customer is never to be made to feel they are wrong.
    2. Always try to find a...
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4