Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.18 seconds; generated 34 minute(s) ago.

  1. Replies
    2
    Views
    203

    What you have is a Craftsman Router Crafter. It...

    What you have is a Craftsman Router Crafter. It lets you make wood turnings (sort of) with your router. I have one and used it a number of times when it was new. You are limited by the diameter...
  2. Replies
    18
    Views
    348

    Maybe it is time to clean the gravel. You will...

    Maybe it is time to clean the gravel. You will be amazed how much dirt is under it.
  3. Replies
    7
    Views
    283

    If you want knockdown capability use this bed...

    If you want knockdown capability use this bed frame hardware for your stringers:
    517607

    For your cross supports use these:
    517606
    I used similar hardware for the wood parts of these day beds....
  4. Replies
    76
    Views
    3,304

    Getting out of bed in the morning can be...

    Getting out of bed in the morning can be dangerous, but then again staying in bed could also be dangerous as lots of people die in bed. We all take various levels of risk every day. If you are...
  5. You can cut pretty nice coves safely on a table...

    You can cut pretty nice coves safely on a table saw with a jig, though they do take quite a bit of time to make the cut. Clean up can be a bit of work if you don't have some raker teeth on your...
  6. Replies
    21
    Views
    1,224

    Don't do this if your lenses are plastic. The...

    Don't do this if your lenses are plastic. The dryer sheet will scratch them. I used a dryer sheet on my face shield and it pretty much ruined the plastic with scratches.

    Bausch & Lomb Savers...
  7. Replies
    26
    Views
    2,876

    Our cat would chew on any flowers we brought into...

    Our cat would chew on any flowers we brought into the house. He particularly went after Poinsettias.

    Plants for cats
  8. Thread: Ants

    by Lee Schierer
    Replies
    20
    Views
    1,080

    Please tell us that the drier isn't exhausting...

    Please tell us that the drier isn't exhausting into the crawl space. If it is blowing the exhaust air into the crawl space, that is a really bad idea. All that moisture will encourage mold and rot.
  9. Replies
    114
    Views
    4,389

    You may have a male holly tree...

    You may have a male holly tree. You need to buy it some friends,,,,,
  10. Replies
    8
    Views
    1,149

    My shop was getting pretty out of control. I've...

    My shop was getting pretty out of control. I've been attacking one small area at a time, starting with my saw table since a friend asked if I would help him with a project. It is still a work in...
  11. Depending upon how long the board you want...

    Depending upon how long the board you want curved, how much curve and how much space you have in your shop you can use make as long a radius as you have room for use a circle cutting jig. They are...
  12. Replies
    14
    Views
    985

    This is what I have done when I have used iron on...

    This is what I have done when I have used iron on banding. For Formica type edge banding I use a laminate edge trimmer on my router.
  13. Replies
    63
    Views
    2,586

    So put a pad on the floor if you want to save the...

    So put a pad on the floor if you want to save the router bit. It is probably easier to replace than the collet.
  14. Replies
    63
    Views
    2,586

    Find a piece of hardwood about 3 feet long. 6...

    Find a piece of hardwood about 3 feet long. 6 inches from one end drill a hole that will just let the router bit fit through. Run some duct tape up and over the back end of the collet so it won't...
  15. Poll: Well it's a tie at the moment, but there is still...

    Well it's a tie at the moment, but there is still time to show your opinion.
  16. Replies
    28
    Views
    2,151

    Based on the amount of burn marks on your cuts,...

    Based on the amount of burn marks on your cuts, your saw is not as well aligned as it could be. It could be your fence is flxing from applying too much pressure.

    When I make rip cuts on my TS I...
  17. Replies
    11
    Views
    774

    I use Adblock plus, but I set it to allow ads at...

    I use Adblock plus, but I set it to allow ads at SMC. Every little bit helps keep the lights on here.
  18. Replies
    7
    Views
    986

    Interesting design. The curved boards in the lid...

    Interesting design. The curved boards in the lid are interesting. I don't think I have ever seen that done before.
  19. Replies
    2
    Views
    506

    Your end grain to face grain joint isn't a very...

    Your end grain to face grain joint isn't a very strong joint. The dowel will help, but to prevent rotation should the glue joint fail, add a small finish nail driven through the side into your...
  20. Replies
    10
    Views
    900

    I used the KV 8450FMP slides...

    I used the KV 8450FMP slides and really like the soft close feature. They are 100# rated. My wife's pantry has a bunch of them in it and they see pretty heavy use.
    517104
  21. I don't see why you can't mount the motor the way...

    I don't see why you can't mount the motor the way you want. It should still work just fine as log as the pulleys are aligned properly. You would still need a way to adjust belt tension.
  22. Replies
    11
    Views
    681

    I've been using Bosch blades on my Bosch...

    I've been using Bosch blades on my Bosch multi-tool. They seem to last longer than the cheaper brands. Their carbide tipped blades hold up really well.
  23. Replies
    3,513
    Views
    883,823

    Sticky: If you didn't read the back you didn't know how...

    If you didn't read the back you didn't know how many box tops you needed to save for the special toy you could get. Like the gray plastic submarines that ran on baking powder. The would dive, sit...
  24. Replies
    18
    Views
    2,494

    When you look at the file size in windows file...

    When you look at the file size in windows file explorer it shows file size in KB. I know that 1,000 KB is 1 Mb. I don't know the upper limit of the site software for photo conversion, but the...
  25. Replies
    18
    Views
    2,494

    516890 The file for the photo above was 9,242 KB...

    516890
    The file for the photo above was 9,242 KB when I uploaded it.

    The photo below was 19,580 KB
    516891

    They both uploaded in less than 40 seconds.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4