Search:

Type: Posts; User: frank shic; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds; generated 58 minute(s) ago.

  1. Replies
    2
    Views
    854

    patching raised panel gouge

    hi guys, any suggestions on how to patch up small router gouges in a raised panel? i was thinking about using either speckling compound or wood filler before running the panel through the raised...
  2. Replies
    13
    Views
    4,640

    building frameless with prefinished plywood will...

    building frameless with prefinished plywood will save you an enormous amount of time in finishing and assembly. most people own face frame kitchen cabinets so frameless cabinets are actually somewhat...
  3. Replies
    26
    Views
    5,717

    i use the kreg only for building jigs and stuff...

    i use the kreg only for building jigs and stuff that doesn't need to be spot-on accurate. i use the PC pocket drilling machine for everything else and have noted a marked improvement in accuracy of...
  4. Replies
    47
    Views
    9,972

    mike, that looks like a professional job. how...

    mike, that looks like a professional job. how long did it take to do all those doors and drawer fronts? did you have a drum sander? really impressed that you made all those cuts with the track saw!
  5. Replies
    21
    Views
    4,149

    use extension supports on either side so the...

    use extension supports on either side so the piece doesn't drop to the ground
  6. great to hear! that makes two happy campers :)

    great to hear! that makes two happy campers :)
  7. you will not regret your efforts in obtaining...

    you will not regret your efforts in obtaining this wonderful machine! ever since i got one of these off of craigslist a few years ago, my joints are actually flush now without going through excessive...
  8. Replies
    25
    Views
    9,691

    those are quite massive drawer fronts! can...

    those are quite massive drawer fronts! can totally understand the extra screws in that type of a situation. btw what are they putting in drawers that wide?
  9. Replies
    25
    Views
    9,691

    so you still need extra screws through the inside...

    so you still need extra screws through the inside of the drawer box? i was thinking that the handle or pull would be enough.
  10. Replies
    25
    Views
    9,691

    the blum drawer adjusters are placed in holes...

    the blum drawer adjusters are placed in holes that allow a little play although you have to drill them on both the drawer front and the box and the surface has little bumps on it to allow some...
  11. Replies
    25
    Views
    9,691

    i use mainly tandemboxes from blum but in the...

    i use mainly tandemboxes from blum but in the future if i were to build a cabinet with false drawer fronts, i would use the drawer front adjusters as previously mentioned. hot glue and some shims...
  12. Replies
    7
    Views
    3,139

    i hate shelf liners as well although i'll bet my...

    i hate shelf liners as well although i'll bet my wife will stick them in everywhere once i rebuild the kitchen...
  13. Replies
    7
    Views
    3,139

    i usually flush the top of the lower rail to the...

    i usually flush the top of the lower rail to the edge of the cabinet bottom so that you can slide stuff out over the rail without having to lift it. i shoot for 4" clearance underneath the cabinet...
  14. Replies
    23
    Views
    7,053

    trevor, just looked more carefully at the...

    trevor, just looked more carefully at the cabinets and realized that they were beaded! what technique did you use?
  15. Replies
    28
    Views
    6,925

    back when i was in my hand tools phase, i really...

    back when i was in my hand tools phase, i really tried hard to cut mortise and tenons by hand but after spending half a year in vain, i decided life was too short to spend sanding everything down by...
  16. Replies
    23
    Views
    7,053

    nice upgrade!

    nice upgrade!
  17. Replies
    20
    Views
    3,113

    the center is raised compared to the sides but...

    the center is raised compared to the sides but you're right semantically.
  18. Replies
    13
    Views
    3,020

    hilarious... great tip by JR though if you feel...

    hilarious... great tip by JR though if you feel like getting out the blowgun.
  19. Replies
    20
    Views
    3,113

    congratulations! time to remodel the kitchen :)

    congratulations! time to remodel the kitchen :)
  20. Replies
    9
    Views
    2,456

    oh that's nifty! how do you make them? what do...

    oh that's nifty! how do you make them? what do you play - lead or rhythm?
  21. Replies
    29
    Views
    14,538

    i'm going to take much greater pains in the...

    i'm going to take much greater pains in the future to make sure that the jamb extensions are as square as possible next time to avoid all the trimming. ever consider becoming a manufacturer? lol...
  22. Replies
    29
    Views
    14,538

    looks great, dave! did you have to do any...

    looks great, dave! did you have to do any additional trimming to get the shutter to fit the opening? i'm toying with the idea of building the frame and the shutter together simultaneously next time...
  23. Replies
    33
    Views
    13,060

    richard, have you figured out which fastening...

    richard, have you figured out which fastening method you'll use? the hidden fasteners look great but almost all of them take a lot more time than face screwing. i used deck master undermounted...
  24. Replies
    16
    Views
    3,717

    another thanks from someone who'll probably never...

    another thanks from someone who'll probably never make it out there!
  25. Replies
    4
    Views
    1,821

    i hope no one else tries that...

    i hope no one else tries that...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4