Search:

Type: Posts; User: David Griffiths; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds; generated 4 minute(s) ago.

  1. Thanks for posting Joseph

    Thanks for posting Joseph
  2. Replies
    5
    Views
    1,530

    Hi David The texture is engraved as well. I used...

    Hi David
    The texture is engraved as well. I used the fill tool from Corel X4 - texture fill - red brick - and altered it until I arrived at a texture the lady wanted. You're right, it is pretty...
  3. Replies
    5
    Views
    1,530

    Thanks gents, It was a good project to be...

    Thanks gents,
    It was a good project to be involved in.
    Regards
  4. Replies
    5
    Views
    1,530

    Experimenting with Balsa Wood

    My neighbour asked if I could help out with her minature house and we came up with some ideas for the foundations, steps, paving and chimney
    We decided to use balsa wood and see what happened.
    The...
  5. Replies
    16
    Views
    2,328

    Frank, I'll be using this method when my tube...

    Frank,
    I'll be using this method when my tube dies. A very effective and cost saving method I must say. Thanks for sharing
  6. Frank, We're either going to have to get super...

    Frank,
    We're either going to have to get super qucik as you suggest or say a polite no!
    I spent around 2 hrs trying to get the tarnish off. The plate was around 200mm (7" ?) in diameter and the...
  7. Rodne We have come across this issue with...

    Rodne
    We have come across this issue with certain types of SS also.
    As soon as the Cermark was dry we lasered. Because the job took around 7 mins to engrave perhaps the extra time was a big...
  8. The makeup of cermark must be every potent. We...

    The makeup of cermark must be every potent. We rubbed and buffed again and again to no avail. I don't think I'll do these anymore. The bond was very good. I'm led to believe the plate may have come...
  9. Removing tarnish from Nickle Plated Plate

    I've just finished laser engraving a Nickle Plated award and I am unable to remove the tarnish marks the cermark has left.
    When I carried out a test on the rear of the plate I encountered no...
  10. Replies
    11
    Views
    6,878

    Thanks Frank, worked a treat, Regards

    Thanks Frank, worked a treat,
    Regards
  11. Replies
    11
    Views
    6,878

    Thanks Lee I wasn't having a shot at your...

    Thanks Lee
    I wasn't having a shot at your programe and not being the best at programing couldn't work it out. I now can work it out thanks to your input.




    If I'm not mistaken, you can...
  12. Replies
    11
    Views
    6,878

    Hi Mike, I run Corel in mm however the Box...

    Hi Mike,
    I run Corel in mm however the Box Making VBA Macro. Called FingerBox.gms seems only to work in inches. As we can only buy our timer in mm and not inches it's time consuming to make the...
  13. Replies
    11
    Views
    6,878

    Box making software

    Hi,
    I've been searching for box making software that was listed here some time back that could use millimetres as well as inches called BoxMaker (?).
    I can't remember if it was a macro for Corel or...
  14. Replies
    5
    Views
    1,962

    Steve Agree with Rodne, Metal has to be squeaky...

    Steve
    Agree with Rodne,
    Metal has to be squeaky clean.
    We had what we thought where plain stainless steel plates. However they had a light clear coating on them. Once we rubbed and rubbed and...
  15. Replies
    13
    Views
    1,762

    Thanks Mike, A couple of good tips in that lot....

    Thanks Mike,
    A couple of good tips in that lot.

    Regards
  16. Replies
    13
    Views
    1,762

    Thanks Doug. You're 100% on the money with the...

    Thanks Doug.
    You're 100% on the money with the issue of the same font being called a miriad of different names. A real pain sometimes

    I thought of the curves, however there is the very odd...
  17. Replies
    13
    Views
    1,762

    Seems I was right. Once my client updated to the...

    Seems I was right.
    Once my client updated to the full version of Adobe, made a few changes to the fonts settings, presto, I can now import direct.

    Thanks to all for your help.

    Regards
  18. Replies
    13
    Views
    1,762

    OK, This has been bugging me all weekend and...

    OK,
    This has been bugging me all weekend and after taking on board all of your guys good suggestions it got me thinking.
    1. Why is it showing up as Helvetic and the other font when it is supposed...
  19. Replies
    13
    Views
    1,762

    Thanks Frank, I emailed the jester font to my...

    Thanks Frank,
    I emailed the jester font to my customer so I'm hoping it's the sme and nothing happened when he installed it.
    I just noticed on another PDF (WITH THE SAME INFORMATION) that what he...
  20. Replies
    13
    Views
    1,762

    Hi Shaddy, Thanks for your responce. When I...

    Hi Shaddy,
    Thanks for your responce.
    When I import the whole doc, I get the attached message.
    I change the Hel. to arial and the other one to Jester and Visa Versa for a trial. When I go Ok the...
  21. Replies
    13
    Views
    1,762

    Importing text from PDF

    Hi all,
    I'm trying to import text from a PDF file that has several fonts in it. (I'm using CDR 12)
    My process is
    Select all text in the PDF
    Select paste special - Select either Rich Text or Text...
  22. Count me in thanks

    Count me in thanks
  23. Replies
    3
    Views
    94,583

    Great find Ramon.

    Great find Ramon.
  24. Replies
    3
    Views
    913

    Thanks guys, All up and going now. Hopefully...

    Thanks guys,
    All up and going now.
    Hopefully one day I'll get the hang of doing this.

    Regards
  25. Replies
    3
    Views
    913

    Epilog new driver - help please

    Ok, I'm not the smartest when it comes to this stuff, so I tried to do this myself, thinking it would be easy. (maybe to others but I'm stugling)

    Here's what I've done.
    Clicked on the the new...
Results 1 to 25 of 46
Page 1 of 2 1 2