I started with rats and got rid of them and the chipmunks moved in. I sent the rat traps out and watched a chipmunk sit on the trap and eat the peanut butter. He was just too little to set off the...
Type: Posts; User: Wayne Hendrix; Keyword(s):
I started with rats and got rid of them and the chipmunks moved in. I sent the rat traps out and watched a chipmunk sit on the trap and eat the peanut butter. He was just too little to set off the...
Take a look at Eureka Zone's website: http://www.eurekazone.com/default.asp You can order shorter and longer tracks directly from them. Rockler and other retailers only carry a limited portion of...
Trailer full of lathes
On the way to school this morning I passed a truck towing a trailer that had 4 or 5 Powermatics probably 3520Bs, what looked like a Robust American Beauty, and a Jet probably 1642. There could have...
Fabric softener can also inhibit water absorption, you should use it on your towels. To clean paint rollers I just use a little bit of dish soap and it leaves them nice and clean and soft.
Check out this video: https://www.youtube.com/watch?v=sQqPm3LmwV4 It looks pretty easy.
I haven't worked on the 5 but it looks similar to the 4. I changed screens and batteries on the 4 and the...
I appreciate everyone's input. Still considering all the options. Several family members are interested in coming out with us so if they can commit for sure we will just have them drive one of the...
Selling was actually the initial plan but we decided to keep it because it is actually a fairly reliable car that I can do almost all the work on. However, once I start factoring in the cost and...
That's something I hadn't considered. I will see if the schools have a rideshare board. I know they used to, I remember using the BYU one a couple times.
This was our first thought, but given the planned trip is 3 days of driving we wanted two people, one in the car with my wife and one with me so we could alternate drivers. We have a 16 month old and...
In June I will be moving from Salt Lake City to Milwaukee to start residency. The easiest and cheapest way we have found for us to move is going to be rent a large truck and tow one of our two cars...
I think the best advice is to buy the best lathe you can afford when you buy one. You can turn smaller things with a bigger lathe but no the other way around. You will also never wish you had less...
Just drill holes as you need them.
I suggest building something simple, cheap and sturdy and figure out what is important to you as you use it, all of us have slight differences in how we work and how we want our work area set up.
...
I have one of these over the desk/craft table in our basement. It is really easy to open up the end and change out the cord. I put 10' or so of lamp cord with an inline switch. Then I plugged it into...
There is a slight difference in the head shape the one in the OP appears to being flat on the bottom and top of the head with a radius between them, while the one at McFeely's has a small bevel on...
It's not a Confirmat screw, its a JCBW screw.
http://www.mcfeelys.com/screws-fasteners/specialty/7mm-x-50mm-jcbw-screws-brass-plated-steel-hex-drive-qty-100-8fmt1.html
McFeely's has them. You...
I got great results using sandpaper, but found it did wear quickly, although I was using really cheap sandpaper.
I used 3M Super 77 spray adhesive to stick it to my plate, it should be available...
Just went though a similar move, mine wasn't so short of notice, but I went from shop space to no shop space. Also I will be moving again next year and will not know what city I am moving to until...
When I installed cabinets we did it to cut the scribe strip to match the wall. The "trick" if you will was first ripping the waste area with the fence and the only trimming off less than the...
I read an article a few years ago, I think it was in Fine Woodworking, where the writer tested if stearated sandpaper would affect the adhesion of the finish. He came to the conclusion that it did...
I have cut acrylic with a 50 tooth combination blade by making two passes over the saw. The first one shallow to just score the cut line and the second pass to complete the cut. Gives me a perfect...
Where is this page you speak of?
I have never seen a single thing that started with this or something similar that was true
Not one ... ever.
Talk to whoever is managing your COPD. If they know there is a specific activity you want to do which the COPD is interfering with they may be able to adjust your medical management to help. It is...
If that is all you are going to use it for I would buy 3/4" OSB rather than plywood. It is cheaper around here.