Search:

Type: Posts; User: Jim Bowers; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    35
    Views
    13,440

    I have used the Infinity insert zero clearance...

    I have used the Infinity insert zero clearance plate for over four years. I have never encountered any problems that I would not expect with other zero clearance plate with other cabinet saws.
  2. Screw from inside of cabinets. Also screws from...

    Screw from inside of cabinets. Also screws from inside near miters to hold tight. Size screws so they do not penetrate the baseboard
  3. Replies
    8
    Views
    3,664

    Stick with the same rotational speed. This saw...

    Stick with the same rotational speed. This saw was designed to rotate at 3450 rpm. This faster the blade the smoother the cut. There is a lot of physics involved in determining what the saw blades...
  4. I have purchased from The Blastgate Co *& Penn...

    I have purchased from The Blastgate Co *& Penn State Industries. You will find 6" with ease.
  5. Replies
    18
    Views
    11,957

    Dovetail joints would work very well. Lock and...

    Dovetail joints would work very well. Lock and unlock with little trouble. Both sides would be very stable when connected
  6. Replies
    53
    Views
    23,167

    Send the blades the complete set and have them...

    Send the blades the complete set and have them give you an estimate on the cost to replace the damaged teeth and have them sharpened
  7. Replies
    18
    Views
    3,678

    I totally agree with Mike. Speed control would be...

    I totally agree with Mike. Speed control would be first thing I would check. It that does not fix problem call Jet Tools.
  8. Mine are Multi-split AC unit, Table saw, Dust...

    Mine are Multi-split AC unit, Table saw, Dust Collector, Planner, Air Compressor. I listed these in the order of use.
  9. I have used this blade for more than a year. I...

    I have used this blade for more than a year. I have not found the need for stabilizers. It is my go to blade.
  10. Replies
    36
    Views
    11,305

    http://high-tech.ie/hitechmachinery/Files/Centauro...

    http://high-tech.ie/hitechmachinery/Files/Centauro_CO_Bandsaws.pdf This is the spec sheet for your saw. I think this will be very helpful.
  11. Replies
    15
    Views
    8,367

    http://www.americanfabricfilter.com/ They will...

    http://www.americanfabricfilter.com/ They will make you a bag in any size you desire. They have several weight bags to meet your requirements. If you call you will find they are very knowledgeable...
  12. Use Compressor Oil. Easy to find in Box Stores....

    Use Compressor Oil. Easy to find in Box Stores. It is non-detergent. Not sure of weight but I bet it is close to SAE 30
  13. I installed a multi split system a year ago in my...

    I installed a multi split system a year ago in my shop. It has one 12,000 BTU air handler, and two 9,000 BTU air handlers. Inside my work area I have one 12,000 and one 9,000 BTU air handlers. I keep...
  14. Replies
    9
    Views
    1,951

    Use a dowel the proper size and cut it off flush...

    Use a dowel the proper size and cut it off flush with the surface. Of course apply glue to part of dowel inserted in hole. Used this method for years.
  15. Check this website for information on Iperjet ...

    Check this website for information on Iperjet http://www.coral.eu/catalogo/iperjetdf
  16. Replies
    12
    Views
    2,828

    This is a mineral stain. You will find it often...

    This is a mineral stain. You will find it often in soft maple lumber.
  17. Replies
    56
    Views
    13,421

    I can not explain SawStop cost in your location....

    I can not explain SawStop cost in your location. However, I own 2 cabinet saws. Both are 3 hp. One is the ICS SawStop. This is my go to saw for most of my work. I have found this saw to be above...
  18. Z-bar is only 1/2 inch projection when installed

    Z-bar is only 1/2 inch projection when installed
  19. Replies
    352
    Views
    62,347

    Please add me to drawing

    Please add me to drawing
  20. Replies
    128
    Views
    40,263

    Please add me to drawing

    Please add me to drawing
  21. Replies
    352
    Views
    62,347

    Yes count me in

    Yes count me in
  22. Please allow me to be in this drawing

    Please allow me to be in this drawing
  23. Replies
    21
    Views
    5,052

    A very good question. Thanks for asking because I...

    A very good question. Thanks for asking because I am sure there are a number of people who will benefit from the answer. Gerry is correct with his answer. Thanks again for asking
  24. Replies
    583
    Views
    77,465

    Yes I could use this bench

    Yes I could use this bench
  25. yes allow me a chance to have this

    yes allow me a chance to have this
Results 1 to 25 of 76
Page 1 of 4 1 2 3 4