Search:

Thank you for the assistance

Bye the way, It is a full set. Side board, chairs and large table.

Sam, I am not sure how they are finished. I will go home and look tonight. The set is from the 60's and is in fine shape. Just wanted to spruce up a bit. If there is no hard finish, and I do use the...

I have a well cared for dining room set of solid teak furniture. I wanted to spruce it up for the Holiday. I was thinking Murphy's Oil Soap and then wipe on teak oil. What do you suggest?

Thanks. It seems as though this will work out well.
I appreciate the input.

Faust,
I have the Sioux as well. I also plan to do all that you said. I already have the extra accessaries you mentioned. I am just getting a bigger compressor. I was going to use black pipe though...

I am in the market for a new compressor primarily to be used for sanding with my Grex RO sander.
I was looking at the Rolair model V5180K30. 80 gallon, 5 hp.
Don't want it to be over-kill, but...

Ok... so maybe the lathe in the "off " position!!

I cannot try my idea out because I am setting up a new shop...
But here it goes... I just bought for a different non-woodturning project, a Ryobi LED flexible inspection scope. How would it work out...

I had the same problem , particularly on soft woods... Removed gaskets, rounded edges, then rubber cemented the o-ring back in place. Problem solved.

Has anybody had experiences with the new Enduro-Var Urethane Varnish on oak hardwood floors?
The quick dry time and no odor is appealing. They suggested applying with a pad finisher and four coats...

Thomas, Here is the plan...
I have put up a plastic vapor barrier sealed with caulk. I put up 2 inch blue foam insulation in between each stud. I plan on using moisture resistant sheetrock. The...

Thomas,
I am in CT.
My concrete walls are bare, untreated, dry and uninsulated. I am starting from scratch.
The basement used to be VERY WET with a high water table the water came up through the...

Guys, I am svery confused about all this...
It seem s that some of you are suggesting that I put the rigid foam directly on the concrete wall uninterupted, and then the 2 x 4 studs on the faom,...

Steve,
I like it lots!! It looks like it wants to be held. I also like the that it looks primitive, perhaps Native American.

Michelle, That is what I was thinking. I am planning on getting a Rolair 5 hp 80 Gal.
It is pricey but I figured it would handle all tasks required.

I am about to make a purchase of a new compressor. I know that sandblasting has specific air requirements. I plan on getting a small counter sandblasting cabinet that would be used for texturing...

I think I am going with the Rolair 5 hp, 80 gallon model. What you think?

Michael ,
I just checked on Lowes website. I looked at the Ingersal Rand and the Cobalt 5hp, they both seem to produce about 17 cfm at 40 psi. Is that good enough for power sanding and sand...

Michael,
I looked at the specs. of several models. They list different CFM for different PSI.
What CFM do I need at what pressure?

Thanks guys. I want to use sheetrock to give it a painted finished look. The walls are poured concrete. The purple foam is thicker than the other colors. I am also wondering what R-value I need. Do I...

I am putting together a new basement shop and I need a new compressor. I now have a 12 gallon Campbell Hausfeld on wheels. It works well but runs often and very loudly. I use it often for power...

My soon to be shop which is now bone-dry due to a trench-sump pump system, I think needs to be insulated before I finish with the sheetrock. I was planning on putting a plastic vapor barier on the...

Greg, Thanks. I am shying away from the Laguna as well for the same reasons. My friend has a Laguna bandsaw and it came with missing motor hardware. He had a real tough time getting it corrected. I...

I guess I should also be looking at the Clear View... 5hp similar price