Search:

Type: Posts; User: Robert Willing; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    2,729

    excellent work

    excellent work
  2. Replies
    11
    Views
    3,639

    I had the same problem!:eek:

    I had the same problem!:eek:
  3. Replies
    34
    Views
    12,701

    I ended up buying the same one and have the same...

    I ended up buying the same one and have the same problems. Not real happy.
  4. Replies
    9
    Views
    2,020

    I like the textured rim the best.

    I like the textured rim the best.
  5. Replies
    35
    Views
    5,100

    Great article.

    Great article.
  6. Replies
    35
    Views
    5,100

    First I would like to thank all of you for your...

    First I would like to thank all of you for your comments. I originally posted this as a question to the group was that I needed to check my TS. It was pushing the wood away from the fence, but than I...
  7. Replies
    35
    Views
    5,100

    How close is close nough

    I am tuning my table saw and the blade and fense are to within 0.005 of being parallel. They each are tilted 0.005".
  8. Replies
    34
    Views
    12,701

    cordless chain saw

    Anyone have any ideas on a cordless chainsaw. Thinking about getting one for cutting wood for turning wood. Any ideas pro con size battery size bar size etc.
  9. use a wrench, i had the same thing happen on my...

    use a wrench, i had the same thing happen on my 7066
  10. Replies
    22
    Views
    3,977

    https://www.woodcraft.com/products/whiteside-pen-m...

    https://www.woodcraft.com/products/whiteside-pen-mill-set?gclid=CjwKCAiAsejRBRB3EiwAZft7sCO_2w6PRinFnn-FEmZZaUA24Lw3gh_x4EU6DXF9CgHekKSQL14Q3RoC_6IQAvD_BwE this is an excellent pen mill from...
  11. Replies
    13
    Views
    3,768

    Try some of this...

    Try some of this https://www.homedepot.com/p/Minwax-1-pt-High-Performance-Wood-Hardener-41700000/100376253 I use this.
  12. You can also wash them off with soap and water, I...

    You can also wash them off with soap and water, I like to use a hand brush to remove the stubber stuff. I dry them on a paper towel. This extends the life of the pad.
  13. Replies
    115
    Views
    21,100

    I did not bother to read all these posts but...

    I did not bother to read all these posts but after two TS accidents in two years I bought a SAWSTOP. The tips of two fingers nearly cut off was enough for me.
  14. This is a Husky from HD for $120.00. I store my...

    This is a Husky from HD for $120.00. I store my tools in the drawers as well as my chuck and sanding supplies. I also made a sharpening station from the crate of my Griz G0766. On the Husky I left...
  15. Replies
    16
    Views
    4,700

    https://www.pennstateind.com/store/LBUFFSYS.html...

    https://www.pennstateind.com/store/LBUFFSYS.html this system is the same as the beall buffing system but is less expensive and it has the correct cloth wheels. It works great and I think less than...
  16. Replies
    8
    Views
    2,361

    https://www.youtube.com/watch?v=3liDhY_zxSc I...

    https://www.youtube.com/watch?v=3liDhY_zxSc I would suggest reviewing all of Lyle Jamieson youtubes on sharpening.
  17. +1 to you Richard I do exactly the same it is...

    +1 to you Richard I do exactly the same it is using the technology of today. I do use a standard gouge to do a lot of rough spindle turning and some finishing. I figure whatever it takes to get the...
  18. I do the same thing with Duck calls (all my calls...

    I do the same thing with Duck calls (all my calls turkey included) but in Teak oil finish for 24 hrs dry than buff after 24 hours of drying.
    How tall is the box W/O the base? I like the decorative...
  19. Replies
    28
    Views
    6,822

    Thanks for the response JKJ and Bill I and going...

    Thanks for the response JKJ and Bill I and going to read these a couple times to make sure I understand all this good info I do suspect the type of wood has a lot to do with the results.
  20. Replies
    28
    Views
    6,822

    OK this thread is going on where fast. What is...

    OK this thread is going on where fast. What is the right angle to sharpen a shear scraper? Do I need a burr? I can't wait on a video too old for all this nonsense. I have watched two videos With...
  21. Replies
    40
    Views
    22,336

    No real problems with my G0766. Great Lathe.

    No real problems with my G0766. Great Lathe.
  22. Replies
    37
    Views
    10,089

    I took your advice and bought a better one along...

    I took your advice and bought a better one along time ago just to have it on hand. I think Newark was the source.
  23. Replies
    37
    Views
    10,089

    Here is the tool rest part # I mentioned before....

    Here is the tool rest part # I mentioned before. After talking with Technical Support, we have created the warranty replacement order #9032598 to send the replacement P0698013 Tool rest lock lever to...
  24. https://www.youtube.com/watch?v=0JKEEX3Br9I the...

    https://www.youtube.com/watch?v=0JKEEX3Br9I the shaft is their niche to their tool use. The shaft allows you to perform a shear cut, but basically they are EWT. AZCarbide sells them as well and I saw...
  25. Replies
    37
    Views
    10,089

    This is the replacement # P0733096

    This is the replacement # P0733096
Results 1 to 25 of 356
Page 1 of 15 1 2 3 4