Search:

Type: Posts; User: Harlan Barnhart; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    4
    Views
    7,239

    Nice. I'm waiting for a picture with all the...

    Nice. I'm waiting for a picture with all the tools and toolholders installed...
  2. Replies
    38
    Views
    6,027

    To the opening post, I have a fein turbo ii and...

    To the opening post, I have a fein turbo ii and find it indispensable. For me it's worth the cost just for the noise reduction, automatic start/stop is a great feature as well and I've never had a...
  3. Replies
    9
    Views
    1,727

    Pictures? Sounds interesting.

    Pictures? Sounds interesting.
  4. Patrick, the design of your project is probably...

    Patrick, the design of your project is probably the important factor here. A bowtie could look fantastic but they can be deployed carelessly as well, not all of us are Nakashima. I would dress that...
  5. Replies
    112
    Views
    32,665

    To the opening post, everything done by the...

    To the opening post, everything done by the domino can be accomplished another way so it is not essential but rather a matter of convenience or efficiency. I've had one for years and I use it several...
  6. Build a large cabinet for it, scrape off the...

    Build a large cabinet for it, scrape off the flakes and seal. Use the old hardware.
  7. Replies
    10
    Views
    5,013

    I've never seen it done, but I suppose it might...

    I've never seen it done, but I suppose it might work, You will get more tenon length if you put the mortises in perpendicular to the miter cut.
  8. Replies
    10
    Views
    5,013

    I've never had a problem putting dominos in a...

    I've never had a problem putting dominos in a carcass miter after it is cut, just keep in mind it is done from the inside so the top and sides must be the same thickness or the outside will not line...
  9. Replies
    10
    Views
    5,013

    Hi David, I agree pretty much with Jack, if you...

    Hi David, I agree pretty much with Jack, if you have a domino, use it, It will work fine for this application. I would put them on three or four inch increments. There are other joints that will work...
  10. Replies
    31
    Views
    5,164

    Strip the galvanization off with a hour or two in...

    Strip the galvanization off with a hour or two in lemon juice or white vinegar. Wet it and let sit overnight.
  11. Some waterlox formulations have changed as well...

    Some waterlox formulations have changed as well to be be voc friendly. Still a great product.
  12. Replies
    11
    Views
    2,393

    I like how you got all that on a small footprint....

    I like how you got all that on a small footprint. The large loop hose storage and the sander sitter look especially convenient. Nicely done. Festool makes something like that for several thousand...
  13. Replies
    18
    Views
    4,641

    By hand. As long as its just a board or two.

    By hand. As long as its just a board or two.
  14. Replies
    14
    Views
    2,508

    283526 Here it is finished. One coat of...

    283526
    Here it is finished. One coat of safflower oil, and two brush coats of shellac, steel wooled to a dull shine.


    283525
    A few detail shots...

    283527
    The through tenons were wedged.
  15. Replies
    14
    Views
    2,508

    I call it the "use the stuff you have" vernacular.

    I call it the "use the stuff you have" vernacular.
  16. Replies
    14
    Views
    2,508

    Hi Jack. Drilling is faster when I'm the one...

    Hi Jack. Drilling is faster when I'm the one doing it...:) I'm not sure where it will end up. I may use it as a bedside table and as overflow seating in the living room.
  17. Replies
    14
    Views
    2,508

    283371 Most of the waste was removed with a...

    283371
    Most of the waste was removed with a chisel.


    283370
    The face of the joint was trued up with a router plane.


    283372
    After some fitting, the joint slid together.
  18. Replies
    14
    Views
    2,508

    283365 Drilling a hole to remove waste is faster...

    283365
    Drilling a hole to remove waste is faster than chopping.


    283364
    Sawing out the waste.


    283366
    Half of a bridle joint with just a little paring left undone.
  19. Replies
    14
    Views
    2,508

    283358 I scored the layout knife marks with a...

    283358
    I scored the layout knife marks with a chisel and cut away a bit on the waste side creating a little wall to guide the saw.
    283357
    Sawing the shoulders.
    283359
    Sawing the tenons. First...
  20. Replies
    14
    Views
    2,508

    283351 I marked the legs using the dovetail...

    283351
    I marked the legs using the dovetail chopped into the top.


    283352
    I carried the marks down the sides of the legs and pared out the waste.


    283353
    After a lot of fitting and...
  21. Replies
    14
    Views
    2,508

    Building a stool

    I rescued a walnut scrap from someone's discard pile. It looked like it wanted to be a stool.

    283333
    I liked the organic edge and wanted to keep it, so I dressed it up a little with a drawknife....
  22. http://www.grizzly.com/products/Ukulele-Kit/H3125...

    http://www.grizzly.com/products/Ukulele-Kit/H3125

    Ukulele kit, $23. Assembly required.
  23. Replies
    16
    Views
    6,659

    I thought the advantage of miller dowels is that...

    I thought the advantage of miller dowels is that glue does not wipe off the full length during installation.
  24. Replies
    8
    Views
    1,161

    It has a metal brackets inset in the back, on...

    It has a metal brackets inset in the back, on each end to hang on a screw. I set them 16" inches apart so they both catch a stud.
  25. Replies
    8
    Views
    1,161

    It depends. It seems there are two different ways...

    It depends. It seems there are two different ways of extracting the oil, one which produces high polyunsaturated fats and the other high monounsaturated. The monounsaturated variety can be easily...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4