Search:

Type: Posts; User: Ole Anderson; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    9
    Views
    503

    I doubt 26 ga snaplock would collapse, yours was...

    I doubt 26 ga snaplock would collapse, yours was most likely the less expensive 30 ga stuff. My setup includes up to 7" 26 ga snaplock, seams sealed with foil tape. Never a problem in a dozen...
  2. Replies
    13
    Views
    736

    Dropped a manhole cover on my big toe 15 years...

    Dropped a manhole cover on my big toe 15 years ago and ended up with fungus under the nail. Having some pain recently so my doctor suggested I try an 8% solution of Ciclopirox anti-fungal applied as...
  3. Replies
    14
    Views
    985

    I set up my router table with a tall fence and a...

    I set up my router table with a tall fence and a flush trimming bit and finished with sandpaper. Works for both solid edging and glue-on. No-go on the trimming tool with wood as they follow the...
  4. Replies
    31
    Views
    2,371

    My Craftsman/Rikon vibrated like crazy until I...

    My Craftsman/Rikon vibrated like crazy until I noticed the drive belt was coming apart.
  5. Replies
    41
    Views
    3,118

    Should have done the question as a poll. In...

    Should have done the question as a poll. In Michigan, it is pop.
  6. Replies
    79
    Views
    9,106

    Looks kind of cool. but frankly, not sure it...

    Looks kind of cool. but frankly, not sure it helps much.
  7. Replies
    79
    Views
    9,106

    516633I went with Formica.

    516633I went with Formica.
  8. Replies
    24
    Views
    2,226

    To me wooden dowels are called dowels, dowel pins...

    To me wooden dowels are called dowels, dowel pins are steel pins ground to a specific diameter. But then I do see a lot of wooden ones called dowel pins on a google search. Go figure.
  9. Replies
    15
    Views
    1,422

    Never start your miter saw in anything other than...

    Never start your miter saw in anything other than the up position. Let it get up to speed, then bring it down into your work. Especially when cutting non-ferrous material with a toothed blade.
  10. Apparently there is a major difference in factory...

    Apparently there is a major difference in factory applied ceramic finish and the DIY version. UV cured in the factory I would guess. And the good ones are 30 mills thick.
  11. Over concrete I would definitely install the...

    Over concrete I would definitely install the required taped-joint waterproof underlayment (likely foam), even if the LVT has a built in underlayment.. Any low spots can be shimmed with underlayment...
  12. Breaking down plywood on anything other than a...

    Breaking down plywood on anything other than a large slider is a nightmare. Track saw to get to manageable sizes, than take it to the TS for precision ripping.
  13. Replies
    28
    Views
    2,937

    Carb varnished up.

    Carb varnished up.
  14. Visited once with my parents in 1962 and saw the...

    Visited once with my parents in 1962 and saw the coals-over-the rim version.
  15. Replies
    37
    Views
    3,567

    Interesting that the OP has not returned yet to...

    Interesting that the OP has not returned yet to rejoin the conversation.
  16. Replies
    17
    Views
    1,912

    I would have thought also, but from the industry...

    I would have thought also, but from the industry guide: "Both high-density overlay plywood and medium density overlay plywood are kinds of hardwood in which a resin is soaked between the veneer...
  17. Replies
    17
    Views
    1,912

    Pretty sure DOT doesn't bother edge treating...

    Pretty sure DOT doesn't bother edge treating traffic signs.
  18. Replies
    64
    Views
    6,794

    I have an Apple watch that I find very useful to...

    I have an Apple watch that I find very useful to keep track of my heart rate while exercising and to check my ECG as I have some arrhythmia and am on beta-blockers after a heart attack. I do like...
  19. Replies
    21
    Views
    2,265

    I have an 8" Delta bench grinder that has served...

    I have an 8" Delta bench grinder that has served me well. Also have a 6" Baldor with extended shafts that runs at half the speed of the grinder.

    514885
  20. Replies
    37
    Views
    3,567

    Jeremy, I see this is your first post to the...

    Jeremy, I see this is your first post to the Creek, welcome! Out of curiosity, have you posted this question on any arborist or chain saw forums? Wondering how you ended up here? BTW I have a MS...
  21. Ice pick and a small tap with a hammer.

    Ice pick and a small tap with a hammer.
  22. Weekly I need to share a 2 gb video with our...

    Weekly I need to share a 2 gb video with our local cable company. I use the free Google Drive with my Gmail account where you just email a link to the recipient. Every few months I need to delete...
  23. Replies
    19
    Views
    1,856

    I miss my oak firewood

    For years I have gotten red oak firewood mixed with a bit of other heavy hardwoods. Takes two years to season, but that is ok. This year I helped my son split 3 face cords of what appears to be...
  24. Replies
    29
    Views
    3,805

    I would prefer to skip the plastic-like finish of...

    I would prefer to skip the plastic-like finish of poly and opt instead for something like Pratt & Lambert #38 varnish. I did 5 wipe-on coats on my Hickory kitchen cabinets. Plenty of protection...
  25. This discussion reminds me of when I designed my...

    This discussion reminds me of when I designed my dust collection system in 2011, I made good use of the Excel program for duct losses that Bill Pentz had in his dust collection website. Website its...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4