Search:

I don't know about the Freud FT3000, but the FT1700 does allow change bits, lock/unlock the motor, and adjust bit height above the table.

The only problem is that the hole to lock/unlock the motor...

Do a search for "keyhole router bit." You'll find plenty of info.

Since you mentioned a plunge base, I assume you are interested in a multi-base kit.

I think the best is the DW618 3-base kit. My "quick-grab" router is the DW618 with a D-handle base. The fixed...

I use splitter whenever possible, even with the GRR-Rippers.

I rule out MJ Splitters - They can't be used in bevel cutting when I need a splitter even more.

I use the mounting bracket from the...

Link to photos.

Al, check your PM. And send me $10 :D

-- Hoa

Most, if not all, stock splitters are attached to the trunion, and tilt with the blade.

Some of the problems of stock splitters are (0) they are too far from the blade, (1) they don't move up/down...

If you can't find the mini ball-bearing drawers slides...

How about "regular-sized" drawers slides attached to the bottom of the drawer? I have a few drawers in the kitchen that way, and am...

This is mentioned several times in this thread:

- You had the blade tilted toward the fence.
- You may want to consider making that cut with the fence to the right of the blade.
- Blade tilted...

Not local, but if you can't find the thick bags else where...

Penn State carries 7 mil bags.

DW744 is a benchtop saw. I don't think you can rewire it for 240V.

Also, how does the saw "bog down"? Does it stall more often? Does it strip the breaker? Does it dim the lights more?

Is...

I just spent $8 for a set of 2 for my Rockwell BS last week. I bought them from an industrial supply store on the way to work.

I did a quick yellowpages search for "bearing" in Dallas, TX and 2...

Charley,

Yes, you can use your Festool with your Ridgid vac.

Take a look at some photos here.

You need a Porter-Cable 73333 Dust Collection System .

Check Home Depot if you have one around. My local stores carry replacement pads for DW and PC. IIRC, the PC pad is $15 and the DW is $17.

I think the DW pad (with 8 holes) also fits the PC.

Brian,

It is simple than I thought it was.

First off, if there is a ball to provide the detents for the turret, remove them and put them away. There are some dimples on the turret and one on...

I removed the turret stop on my 618 plunge base. Then one day, I decided to put it back. I can't remember the details, but I think I put a steel washer underneath the turret. I applied a layer of...

No problem there. That's where I order most of my hardware (knobs, pulls, drawer slides, ...).

With the shipment, they send you a 10% (or 15%)-off code for the NEXT order. You may want to call...

Bring one to a local bearing shop (check Yellow Pages). Tell them you need the best sealed available.

I bet you the price will be less than $5 each (likely China-made, but they are all like that...

Calvin,

I have to go against the grain here....

My first 6" sander is an RO150FEQ. I bought it when it first came out.

Later, I ran into a new Porter Cable 7336 (same motor as the 7424) at...

Its brother model PC42700 can be modifed to use with Dewalt routers, or most routers for that matter. The only difference between the PC42690 and PC42700 is that the PC42700 has a longer bar, which...

I had one, buying from a garage sale.

It is built like a tank (good) and operates like one (bad). It is really clumsy and difficult to control. Also, it wastes PSA sanding strips because you can...

How wide is the overall width of the miter slot? The diameter of the "foot" that slides on the TS top of the Unifence is 1 3/8". If the overall width of the miter slot is less than that, chances...

This is an idea.

Will you cut half lap joints in 4X lumber? Will you use a sled when cutting dados/rabbets?

If yes, you'll be happier with an 8" set.

It's true that an 8" set has greater speed than that of an...

The fence itself is NOT supposed to touch the TS top. I'm not sure how the UHMW will help.