Search:

Type: Posts; User: Buck Williams; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    2,109

    I remember at one time, thinking of this one by...

    I remember at one time, thinking of this one by Woodsmith, seemed to be a well thoughyout design.

    https://www.woodsmithplans.com/plan/fold-down-workstation/
  2. Replies
    6
    Views
    1,645

    It's most likely a Cutler Hammer BR series load...

    It's most likely a Cutler Hammer BR series load center. There are a number of manufacturers who use the same style bus bar in their load centers, and their breaker will snap into a BR load center....
  3. Replies
    9
    Views
    4,397

    Thanks for the info, haven't dug deep enough into...

    Thanks for the info, haven't dug deep enough into piano humidifiers to get past the installer level, good suggestion, funny it didn't occur to me. Nice cabinet Ken, like the DIY approach to the...
  4. Replies
    9
    Views
    4,397

    Guitar Cabinet / Humidifier

    I'm considering building a cabinet for 5-6 acoustic guitars, that would also humidify the cabinet during the dry winter months. One big question, in my mind is what to use to add to and control the...
  5. That ended up being the only way that I could...

    That ended up being the only way that I could find to get out. By design, I suspect, it took an exhaustive search of "manage you account" etc, " contact us" , (nobody replied to my email), easy to...
  6. Replies
    20
    Views
    3,000

    Good $15.00 solution, that will come in handy in...

    Good $15.00 solution, that will come in handy in the future, not necessarily "fine" woodworking, but a quick solid solution. Great idea
  7. Replies
    18
    Views
    7,097

    If you're thinking about feeding the sub panel...

    If you're thinking about feeding the sub panel with one 50 amp GFI breaker, you should think about what would happen if that breaker tripped because of a ground fault. All of your lighting is out,...
  8. The all around quality / fit and finish of the...

    The all around quality / fit and finish of the saw is suspect, if you paid with a credit card, notify the credit card company that you would like to have them rescind their payment until the dispute...
  9. Replies
    8
    Views
    1,736

    Baltic Birch Plywood comes in 3mm - 1/8"...

    Baltic Birch Plywood comes in 3mm - 1/8" thickness. Birch and Maple are close to each other in my eye.
  10. Replies
    15
    Views
    5,297

    Very nice, I have a pedestal desk that I made...

    Very nice, I have a pedestal desk that I made 15-20 years ago and daily use has taken a toll on the top, which was made with a frame of 5/4 oak with 1/4 oak ply panels flushed up with the frame. (a...
  11. Replies
    5
    Views
    1,375

    good point Max, I'm going to build a Craftsman -...

    good point Max, I'm going to build a Craftsman - Prairie style radiator enclosure out of cherry to hide the radiator, and have the front be removable by using some knock down hardware, no reason that...
  12. Replies
    5
    Views
    1,375

    Thanks - hadn't considered the sub top, shouldn't...

    Thanks - hadn't considered the sub top, shouldn't be a problem, haven't selected the tops or an installer yet, I'll check with them when I do. My cost of doing that vs paying someone to do it,...
  13. Replies
    5
    Views
    1,375

    Kitchen Countertop Extension

    328396Looking for how best to extend a kitchen countertop run, over a radiator that needs to be accessible. There is about 36" x 24" space between the end of my cabinet run and the wall. Countertops...
  14. Great idea, if it isn't official, I think I can...

    Great idea, if it isn't official, I think I can give you a run for your money on that "Village Idiot" title.
  15. Replies
    11
    Views
    2,122

    I'm no expert on the Nat'l Electrical Code, I do...

    I'm no expert on the Nat'l Electrical Code, I do know from being around some construction sites that there is a restriction as to how high a panel can be installed. I Googled "NEC maximum load center...
  16. Mike, Here you go, there are a lot of...

    Mike,

    Here you go, there are a lot of manufacturers out there, the generic term is "Bell Box", basically a cast aluminum box with threaded hubs and gasketed covers, rated for wet locations. The...
  17. Replies
    10
    Views
    1,691

    Just a guess here, maybe a center style would...

    Just a guess here, maybe a center style would accentuate length and make them appear taller. Visually what bothers me is that they feel short and wide, the divider on the smaller door really...
  18. Poll: I work in a cramped basement shop, a mitersaw...

    I work in a cramped basement shop, a mitersaw cart/cabinet on casters with fold down wings is the answer for me. The foot print is relatively small, the wings are set up with T-tracks and stop blocks...
  19. Replies
    37
    Views
    16,981

    Sounds like a perfect time to get familiar with a...

    Sounds like a perfect time to get familiar with a cabinet scraper, I wasn't familiar with them until I stared hanging out here, my first use was a real AHAH moment.
  20. Replies
    41
    Views
    12,378

    I get that Mike, I think I might have married her...

    I get that Mike, I think I might have married her sister.
  21. Replies
    41
    Views
    12,378

    I guess that was the kind of the point of the...

    I guess that was the kind of the point of the question, whether Shaker was a marketing term or whether or not it was a real Shaker design feature. Certainly wasn't trying to call the OP or anyone out...
  22. Replies
    41
    Views
    12,378

    Can I ask a question somewhat related to this...

    Can I ask a question somewhat related to this topic? I'm no expert on Shaker furniture, I have a few Thomas Moser books and have read a few books on Shaker furniture, looking for design ideas and...
  23. Replies
    31
    Views
    6,780

    My bet is on it being ash. If you notice a sweet...

    My bet is on it being ash. If you notice a sweet barley malt, malted milk smell when cutting or milling that's a sure give away. I love that smell.
  24. Replies
    13
    Views
    8,253

    I'm not quite sure what your install looks like,...

    I'm not quite sure what your install looks like, you can often use a *(trade name) Minerallac conduit hanger as a kind of a stand-off so that you can run your conduit straight in to the 1" KO in the...
  25. I've used a track saw and a diamond blade to cut...

    I've used a track saw and a diamond blade to cut soapstone, EZ-Smart with a Makita circular saw, worked well. Soapstone is much softer than granite, and doesn't require a wet cut, that as Ian said...
Results 1 to 25 of 162
Page 1 of 7 1 2 3 4