Search:

Type: Posts; User: Ralph Barhorst; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    22
    Views
    3,726

    I could be wrong, but it sounds to me like it is...

    I could be wrong, but it sounds to me like it is just not wired correctly. On 110V it probably is only running on one of the two 110V windings causing the slow startup or the motor could be connected...
  2. What Joe said; use 1/4 sawn or straight grained...

    What Joe said; use 1/4 sawn or straight grained wood to reduce the problem
  3. Replies
    2
    Views
    1,248

    I wanted to go to that sale but had to go to a...

    I wanted to go to that sale but had to go to a wedding instead. I have been to their spring sale several times and came back with some great buys.
  4. Don - Check out this post. ...

    Don - Check out this post. http://www.sawmillcreek.org/showthread.php?t=77289
  5. Jim, It works on SMC, at least on my computer.

    Jim, It works on SMC, at least on my computer.
  6. Here is how to magnify your computer screen

    My eyes are getting old and weak. Therefore, I use the commands that Bill Gates gave us. There are two different ones that I like to use.

    1. Hold the control key down and roll the roller on...
  7. Replies
    7
    Views
    1,701

    Has anyone used this Japanese plane?

    I want to know if this will work on white oak? How much does it cost?

    http://www.youtube.com/watch?v=uWQFlSa4prM
  8. Replies
    7
    Views
    1,174

    I use endmills all the time, especially for...

    I use endmills all the time, especially for mortise and tenon joints. I usually get them from ebay. They are much cheaper than the router spiral bits. The best ones to use are 2-flute solid...
  9. Replies
    13
    Views
    2,957

    Thanks Chris and everyone else for the nice...

    Thanks Chris and everyone else for the nice comments.

    How did you make the small thin strips of wood that were the inlays?
    They weren't inlays. They are 1/4" x 3/4" strips of maple and...
  10. Replies
    13
    Views
    2,957

    Mahogany Hall Table

    I finally completed my Hall Table. It is primarily made from Mahogany. The top and the shelf utilize a veneered panel of MDF with a mahogany frame. The veneer is curly bubinga. The accent wood is...
  11. Replies
    11
    Views
    1,385

    I don't think it would make much difference which...

    I don't think it would make much difference which plywood you use, but you might want to use an exterior grade.

    You will like that varnish. I used it about 4 years ago on some white oak garden...
  12. Replies
    2
    Views
    1,831

    Folding Computer Table

    Several years ago I built this table, and it should work fine for your application. The dimensions are almost exactly what you need. I used butternut for this table. the third photo shows the table...
  13. Replies
    19
    Views
    3,305

    I use endmills for spiral router bits and I...

    I use endmills for spiral router bits and I always get them from ebay.
  14. Replies
    16
    Views
    5,649

    I like to use a piece of rubber innertube to...

    I like to use a piece of rubber innertube to clamp my boxes. I had a couple of old truck inner-tubes and I cut out some 1" wide strips that are about 8' long. Stretch the rubber strip and wrap it...
  15. Replies
    9
    Views
    2,519

    Wedding Box

    My nephew got married on Saturday. We gave him and his wife this box for a wedding present. The top is made with Jatoba and Maple with a Mahogany ‘rings’ inlay. The top was also laser engraved by Tim...
  16. Replies
    1
    Views
    1,907

    Gloat!! Grizzly G1073 16" bandsaw

    I just brought this beast down the basement into my shop. I had to disassemble it to get it down. It will take a while to get it put back together again since I have to rewire it for 115V. Also,...
  17. Replies
    6
    Views
    6,517

    Sears Craftsman jointer question

    I have a chance to buy a Sears Jointer for $150.
    Model 113.232200
    6-1/8" Cast Iron 1-3/8 HP.

    I have not been able to find out much about it on the net. Does anyone have one of these and if so,...
  18. Replies
    3
    Views
    876

    Where can I get this engraved?

    I have a nephew who is getting married in August and I want to make a "wedding box" and maybe a cutting board for their wedding present. I would like to use the design shown below for both the box...
  19. Replies
    5
    Views
    840

    This is great wood art.

    http://www.hardwoodlumberandmore.com/Hardwood/Newsletters/052109.html
  20. Replies
    10
    Views
    2,002

    The length of the side with a 3" inside diameter...

    The length of the side with a 3" inside diameter


    inside length = diameter / 2.61313 = 3/2.61313 = 1.29155"

    Outside length will depend on the thickness of the material.
  21. Replies
    63
    Views
    10,806

    HUH! My neighbor is better than your neighbor.:) ...

    HUH! My neighbor is better than your neighbor.:)

    Last fall my leaves were blowing into his yard and he came over and raked all of my leaves. He is a little anal about his yard.
  22. Replies
    8
    Views
    1,182

    Here is a picture of a box that I made using the...

    Here is a picture of a box that I made using the original 8 inch Incra Jig and my router. It took a while to design and a lot longer to make, but it is not really all that difficult. I used a 3/8"...
  23. Count me in. Thanks, Ralph

    Count me in.

    Thanks,

    Ralph
  24. Count me in Keith. Thanks, Ralph

    Count me in Keith.

    Thanks,

    Ralph
  25. Me too. It is a nice piece.

    Me too. It is a nice piece.
Results 1 to 25 of 364
Page 1 of 15 1 2 3 4