Search:

Type: Posts; User: Brian Kent; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.27 seconds.

  1. Replies
    13
    Views
    2,024

    No. I had not heard of that. What kind of paper?

    No. I had not heard of that. What kind of paper?
  2. Replies
    13
    Views
    2,024

    Turning 10" plates from 4/4 wood.

    I am making many plates from 3/4" thick sapele.

    I have finished 12 of this set using glue blocks.

    The only problem has ben when I turn off the glue block, sometimes the grain gets messy in...
  3. Replies
    24
    Views
    18,781

    I am in the middle of this repair now. I was...

    I am in the middle of this repair now. I was surprised to find my nylon gears in pretty good shape. They had become slightly too far apart and the corner lift assemblies too gummed up. Since I...
  4. Replies
    24
    Views
    18,781

    Have you had any further problems with a PLASTIC...

    Have you had any further problems with a PLASTIC miter gear? I am ordering the same product now.
  5. Replies
    7
    Views
    1,081

    I am re-thinking that. It seems to be jammed to a...

    I am re-thinking that. It seems to be jammed to a halt instead of slipping, so I can try a deep clean if I figure out how to get inside.
  6. Replies
    7
    Views
    1,081

    2 Desktop Planer questions

    My Delta drum sander has served me well, especially since I got it 14 years ago for $150. But alas, the gears are stripped that raise and lower the table.

    I am thinking of getting rid of it and...
  7. is the Bosch 1295 supposed to spin freely?

    I just changed an old backing pad on a Bosch 1295 dvs Random Orbit Sander. The new one spins freely and I don't know if that means it's broken. Is it supposed to do that?
  8. My Annual Communion Chalice gifts for newly ordained colleagues.

    For the last ten years I have made communion chalices for all of the newly ordained United Methodist pastors in Southern California and Pacific Islands.

    This year I made them from laminated 8/4...
  9. That is no problem. So far!

    That is no problem. So far!
  10. Can I finish a chalices without starting with de-waxed shellac?

    My standard finish for chalices for the last 7 years has been a couple of coats of Zinnser's Sealcoat De-waxed Shellac, followed by 5 to 9 coats of wipe-on Poly, and sometimes finished with a wax....
  11. Replies
    13
    Views
    2,027

    I found a way to get the bent part out. Grizzly...

    I found a way to get the bent part out. Grizzly will check to see if they have one the right size. Harvey industries have been helpful but do not have the spare part. If I can't get one I will see if...
  12. Replies
    13
    Views
    2,027

    What size hex key would fit the set screw: SET...

    What size hex key would fit the set screw: SET SCREW M6-1 X 6I am trying to loosen the pulley to free up the bent pin.

    Thank you
  13. Replies
    13
    Views
    2,027

    Thank you. And since the pin is wedged tight in...

    Thank you. And since the pin is wedged tight in there, are bolt cutters a legit option for removal?
    Or a hacksaw with extended end of blad?
  14. Replies
    13
    Views
    2,027

    Here is the photo. I tried to unscrew it but the...

    Here is the photo. I tried to unscrew it but the pin is jammed in against the pulley.
  15. Replies
    13
    Views
    2,027

    Richard, does the chrome angled part that holds...

    Richard, does the chrome angled part that holds the pin unscrew? Is that part of the assembly?
  16. Replies
    13
    Views
    2,027

    Need to replace a spindle lock pin

    The lathe is a Grizzly GO800, which is a Harvey Tool lathe, basically the same as a Laguna.

    User error - started up a 12" a 2" bowl blank while the spindle lock pin was still in. I have done this...
  17. Replies
    6
    Views
    770

    Bondo or epoxy for Wood rot?

    I have a porch cover with wood rot on a couple of overhang beams. The wood is a 4x8 by about 2 feet. I would like to try scraping, treating for rot and insects, and filling.

    My two choices appear...
  18. Replies
    10
    Views
    29,605

    Yes, I am interested in chip carving. I am...

    Yes, I am interested in chip carving. I am laughing at my own insecurity about seeing a knife that close to your thumb. So is the hock blade your recommendation for the first. I use Shapton glass...
  19. Replies
    10
    Views
    29,605

    Thank you, John. You gave me a lot to go on. I...

    Thank you, John. You gave me a lot to go on. I have a lot of local avocado wood, as well as a little basswood, so I may try both.
  20. Replies
    10
    Views
    29,605

    Time to start learning letter-carving.

    Started out with furniture, and then wood turning. I have made hundreds of communion chalices and patens.

    Now a great friend has asked me to carve the letters GOT (Game of Thrones) in Trajan Pro...
  21. Replies
    13
    Views
    4,042

    Yes, all but the 3 on the far right.

    Yes, all but the 3 on the far right.
  22. Replies
    13
    Views
    4,042

    There are 20 chalices total, (18 in photo) for...

    There are 20 chalices total, (18 in photo) for the 20 new pastors being ordained in our conference.
  23. Replies
    13
    Views
    4,042

    This one is done except for final coats and...

    This one is done except for final coats and buffing. I have a lot more of this twisty and holey stuff so I can try the other ideas too.
  24. Replies
    13
    Views
    4,042

    That was choice #2. I'll try to make the epoxy...

    That was choice #2. I'll try to make the epoxy work
  25. Replies
    13
    Views
    4,042

    Filling a stem with epoxy resin

    Here is my challenge. I have a deep knot hole between the stem and base of an olive wood chalice. I lined the hole with gold-ish leaf. Now I want to fill it with clear epoxy resin.

    I am looking...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4