Search:

Type: Posts; User: stan kern; Keyword(s):

Page 1 of 17 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    7
    Views
    1,004

    square corners

    have a look at the raised panels from MDF used an 1/8 bit and the corners are very near square, almost off as square
  2. Replies
    0
    Views
    320

    drawing a bald eagel

    http://youtu.be/owBpp9dLDm8 bald eagel trace
    this shows a complex diagram being traced out and resulting a *.dxf file that is machineable
  3. logic trace dxf cnc software releases new drawing board

    Just received the new drawing board vi from john walsh ,its huge and will be able to handle large traces
    Its 70x54 inch overall with a 44x60 in drawing capacity resolution of 1000
    ...
  4. Replies
    0
    Views
    402

    last copy to mdf raised panel

    Took one kitchen cabinet door done some time back and copied it to machine out in mdf ,the detail is very good
    took about 53 min which seems to be the longest one yet

    http://youtu.be/i4fP9jL5UR4...
  5. copied a red oak raised panel profile and duplicated the profile in mdf

    http://youtu.be/LXiIw79O_ys

    the mdf panels are starting to look pretty good,this one took 39 min cnc time and 3 bits 1/4 ball 1/8 ball and 1/4 endmill
    Kept the feed about 140 in/min to...
  6. Replies
    2
    Views
    501

    I think its amazing and the time was wrong it was...

    I think its amazing and the time was wrong it was 42 min, and that could be cut back a bit
    There still is a small radius but very small
  7. Replies
    2
    Views
    501

    3rd and final run at a raised mdf panel

    http://youtu.be/3zlrXA9tq-w
    this turned out very good,the panel looks like an assembled wood door
  8. Replies
    6
    Views
    531

    back

    I agree there is mdf and there is, but this was a project I picked.
    And I just wanted some POS material for a test run and the mdf I had I could not pull down on my own so I found some other...
  9. Replies
    6
    Views
    531

    2nd run at a raised panel

    this was a better run,took 27 min and it turned out well

    http://youtu.be/SQl37ihV2kY
  10. Replies
    2
    Views
    491

    I could not find a piece of mdf so I used plywood...

    I could not find a piece of mdf so I used plywood and only 2 spots popped out and it was very smooth as I used a 8% stepover.
    Mdf when sprayed or painted will be fine and its not done as rails and...
  11. Replies
    2
    Views
    491

    ist run at a raised panel

    the project was to try and program a raised panel and make it look like a frame with a shaped panel
    not a routed pathe
    Its getting there ,just a bit too slow ,next one should be better
    ...
  12. Thread: drawings

    by stan kern
    Replies
    6
    Views
    747

    Have a look at this site ,makes drawing easy...

    Have a look at this site ,makes drawing easy
    http://www.logicgroup.com/

    this shows a trace http://youtu.be/YUCzJ9YBZpw blue herron
  13. Replies
    3
    Views
    954

    blue herron trace

    http://youtu.be/YUCzJ9YBZpw blue herron
  14. Replies
    3
    Views
    954

    I like your diagrams

    I like your diagrams
  15. Replies
    0
    Views
    714

    arch top guitar full size plans to dxf

    Using the logic trace cnc dxf program I digitized an arch top guitar top and bottom
    easily

    http://youtu.be/LMXKcLl0i-k
  16. creating the file for a fitted dreadnaught D28 guitar case

    http://youtu.be/jH6awTnMvko

    dreadnaught D28 fitted guitar case
    This was easily traced even though it did not sit flat on the table
    I did it in 2 parts and fitted it together and increased the...
  17. Replies
    3
    Views
    954

    drawing software different selections

    http://youtu.be/rIk0ToiDfGs

    using logic trace cnc dxf software using trace and curve fir thro points
  18. Replies
    0
    Views
    636

    2013 logic trace cnc dxf program

    I was asked by a few to produce some demos showing the table setup and some selections on the software
    for tracing

    http://youtu.be/IddM_NwSkm8 setting up tablet works and the cnc draw program
    ...
  19. Replies
    3
    Views
    659

    I guess there could be worse things ,I always...

    I guess there could be worse things ,I always wanted something flexible like this for display and this is
  20. Replies
    3
    Views
    659

    cutting and assembling body parts

    Found this pdf file on the human body ,converted it to a *.dxf file ,sized it and cut it on the co2 laser
    took about 8 min for the cutting and a bit more for assembly ang getting the right brass...
  21. Replies
    2
    Views
    795

    thanks a lot

    thanks a lot
  22. Replies
    2
    Views
    795

    sea turtle display part3 final

    Sea turtles swimming -part 3 completion.
    It took 5 hrs cnc time for the *.stl files on the turtles,then it was 9 hrs shop time for the base prep
    driftwood cutting ,sanding ,laquering and final...
  23. Replies
    1
    Views
    739

    sea turtles swimming part2

    After doing the sea turtle in basswood ,i then started the laminating of black walnut for the final 3 turtles.
    The thickness had to be right on to match up with the dimensions i used to create the...
  24. Replies
    2
    Views
    763

    thanks I appreciate the good comment

    thanks I appreciate the good comment
  25. Replies
    2
    Views
    763

    sea turtles swimming

    Came across these turtles swimming and i liked the look ,so i have started to put things together and i wanted a run on how the turtle would look
    before laminating black walnut
    Basswood is great...
Results 1 to 25 of 416
Page 1 of 17 1 2 3 4