Thom
I have a Clearvue kit with the original 5 HP motor new in box. I've replaced with a 3 phase motor and would like to sell it.
Let me know if your interested and I'll post it on the...
Type: Posts; User: Kenny King; Keyword(s):
Thom
I have a Clearvue kit with the original 5 HP motor new in box. I've replaced with a 3 phase motor and would like to sell it.
Let me know if your interested and I'll post it on the...
I bought a refurbished DW 735 from them several years ago. No problems.
Ken
Jeff
Thanks for the excellent deal!!! I hadn't gotten around to installing it and didn't intend to, so I put it up for sale... at the same price.
I got a lot of interest and so I started...
I've retrofitted my Dewalt 735 planer with a Shelix head that I bought off a member here.
The installation instructions are good, but you need a snap ring tool to remove some of the parts. Also,...
I'm looking for a 4 1/2 smoother plane. When compared to say a bailey 4 1/2 or a bedrock 604 1/2, i understand that i BU plane with a high angle, say 50 deg. is good on difficult wood. Is the...
I'm considering the purchase of a 1950's era Boice-Crane band saw. It has 1 HP motor 14" throat, and 8" height capacity.
It doesn't have a fence. Does anyone know if a fence can be purchased...
thanks very much for the helpful responses.
Ken
What is a good source for ApplePly and prefinished ply in the philly area?
I found out that Tague has apple ply. They don't have prefinished ply though.
How about hardwood ply's, cabinet...
I also recommend John Bridge's Tile forum and have gotten great info on that sight.
Based on reading and experience, I believe that a latex additive to the grout will make it more flexible and...
jason, joe
it sounds like i'm spraying too heavy. i was wondering if folks used a seperate gun for edges, but it doesn't sound like it.
Jason, your right about going heavy. On the first...
I've been spraying 2# shellac, also known as "sanding sealer" made by zinnser, with my HVLP conversion gun.
I've been spraying shelves for a wall cabinet i'm making. The shelves are made from...
I have a GI 185 left tilt contractor's saw. It has lots of iron on the table top and a beismeyer licensed fence made in canada. Compared to all of the other comparable saws in the market, this...
Thanks for the responses. I have plenty of turns on the nut for the dado, ie., way more than 3, but thanks for pointing out that possibiliy. It sounds like there might be a burr on the chippers or...
I have an 8" stacked dado set I picked at a woodworking show in PA made by ridge carbide. It seems like a decent set. I had one of the chippers reground for no cost since it wasn't quite even with...
try using a gel stain to prevent blotching due to differing densities in fir, which is similar to pine as far as staining goes
- ken
Rodney
Try Jamestown Distributors. This System Three starter kit might be just what your looking for:
...
jim
thanks, I'll give it a try.
- ken
I've been using my Wagner HVLP spray gun to re-finish an old oak armoir built in, circa 1895 This has a couple of challenges since it's a built in. One is lighting and the other is that the built...
Sanding sealer is just a thinned poly with some "stearates" to make it powder quicker when you do your first sanding. The floor guy pro I rent and buy from suggested that regular poly would be good...
I was able to get the Hitachi M12V for about $120 through Amazon. I mounted that on the router table on the LHS of my contractor saw. I use the Dewalt 618B - 3 base for all hand routing jobs. I...
I'm trying to determine how big of a fan I need for a spray booth. This would be a wall mounted fan mounted to a window opening - just the fan, no window.
I'm planning on spraying water based...
thanks for the responses... i'll have to check out homestead. Someone recommended Hartville tool for casters, and I later found out that they sell Whiteside router bits for a decent price... but I...
Please post any suppliers that your happy with. I would especially like to find the best (cheapest) suppliers for Target USL and Furh finishes. I'm also interested in dewaxed shellac and other...
The fifth picture which should show the curved torsion box ribs didn't post. I'ld sure love to see 'em. :)
- ken
i had the same question about a year ago. i was advised to get the 8" jointer. I bought a 6" yorkcraft from wilke and traded it in 6 months later for an 8" jointer.... definitely get the 8" if you...