Search:

Type: Posts; User: Bryan Hunt; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. I got a 1 - 1/4" spindle and the router spindle...

    I got a 1 - 1/4" spindle and the router spindle that uses ER25 collets.

    I'm a bit confused on the speeds. The chart on the side says it uses 4 gears, but when you take the cover off, there are...
  2. I also have the Airtight clamps from Mac. I use...

    I also have the Airtight clamps from Mac. I use them all the time on my Hammer K4 slider. They were expensive, but they are built like a tank and worth every penny.
  3. New toy (Felder F 700 Z shaper) and question for fellow shaper owners

    I finally got my Felder F 700 Z shaper. I've run a couple of boards through it, and so far, I absolutely love it.

    A question for fellow shaper owners - what feed rate do you typically use on your...
  4. I got our new 5 panel door for the master bedroom...

    I got our new 5 panel door for the master bedroom out of the spray booth and installed.
    I filled some knots and cracks in the Hard Maple cornhole boards I'm working on for a buddy.
    I started an...
  5. Hard Maple and Walnut Roubo split-top bench

    I completed my new Roubo split-top bench. I used the plans from Benchrafted, but made it a bit wider and taller. The top measures 87" long by 29" wide. I set the height to 43". This was my firs...
  6. Replies
    47
    Views
    4,045

    My Christmas tool should be in Dallas by now and...

    My Christmas tool should be in Dallas by now and hopefully in route to me next week. I'll post pics when it arrives :).
  7. Thread: Loft bed

    by Bryan Hunt
    Replies
    14
    Views
    3,239

    Here, I'm fitting the wedged pins. There was a...

    Here, I'm fitting the wedged pins. There was a lot of hand fitting because holding an exact angle with a chisel in Hickory is not very easy.

    487937487938487939

    Finally, the finish. I sanded...
  8. Thread: Loft bed

    by Bryan Hunt
    Replies
    14
    Views
    3,239

    I added a chamfer with a hand plane to the tops...

    I added a chamfer with a hand plane to the tops of the legs.

    487930

    Now the glue-up. I only glued 1/2 of a side at a time because I was worried about the open time and getting all of the...
  9. Thread: Loft bed

    by Bryan Hunt
    Replies
    14
    Views
    3,239

    The sides were joined with though tenon and...

    The sides were joined with though tenon and wedged pins. The narrower boards got vertical wedges while the wider boards got horizontal wedges. In hindsight, I should have gone will all horizontal...
  10. Thread: Loft bed

    by Bryan Hunt
    Replies
    14
    Views
    3,239

    One of the tenons was a bit challenging ... ...

    One of the tenons was a bit challenging ...

    487918487919487920

    I clamped a block to the face and used it as a saw guide. I then used a combination of chisels and router plane to finish the...
  11. Thread: Loft bed

    by Bryan Hunt
    Replies
    14
    Views
    3,239

    The build started with 6/4 Hickory. The legs...

    The build started with 6/4 Hickory. The legs started as 8" wide boards that I ripped down the middle, book matched and laminated. One of the boards had a bad twist in it. By the time I got it flat,...
  12. Thread: Loft bed

    by Bryan Hunt
    Replies
    14
    Views
    3,239

    Loft bed

    My youngest son asked me to build him a loft bed. I said sure, no problem. I figured it would't take too long. I was wrong! 340 hours later (translates to about a year - only working the...
  13. Yep, I posted on Craigslist this morning :)

    Yep, I posted on Craigslist this morning :)
  14. Bump - still available.

    Bump - still available.
  15. Bump - still available.

    Bump - still available.
  16. Still available.

    Still available.
  17. Replies
    15
    Views
    2,396

    I have Shiner Bock in the fridge. You are...

    I have Shiner Bock in the fridge. You are welcome to stop by.
  18. Replies
    15
    Views
    2,396

    Christopher, You are welcome to stop by and see...

    Christopher, You are welcome to stop by and see my shop. I also have a slider you can check out.
  19. Replies
    127
    Views
    19,644

    Hey Kurt, I own a Hammer K4. If you have any...

    Hey Kurt, I own a Hammer K4. If you have any questions about that specific saw, I'm happy to help.
  20. FS Powermatic 15S planer with spiral cutter

    I recently upgraded to a planer/jointer combo so I'm selling my Powermatic 15S with spiral cutter. It has a Wixey DRO and the blades were changed about a year ago. $2500. I'm in Leander, TX which...
  21. Replies
    15
    Views
    2,396

    New planer/jointer combo arrived

    I just upgraded my 8" jointer and 15" planer to a Felder AD941 16" planer/jointer combo. This thing is a beast. I'm fortunate to have a nice neighbor with a forklift. I ran some Hickory through it...
  22. Replies
    35
    Views
    4,794

    Where to buy a saw set?

    I know there are several threads on this, but I'm asking again because Tools for Working Wood and Lee Valley seem to not sell saw sets any longer. Does anyone have a resource for purchasing a...
  23. Replies
    5
    Views
    1,115

    Shout out to Lie Nielsen customer service

    I broke a handle for one of my Lie Nielsen chisels while chopping a mortise this weekend. Lie Nielsen is sending me a replacement at no charge. I've had my chisels a long time and this is the...
  24. Replies
    44
    Views
    5,718

    I got a VFD for my CNC spindle from...

    I got a VFD for my CNC spindle from https://wolfautomation.com. I went with a TECO Westinghouse model and have been very happy with it. There is a learning curve on programming the thing, but it is...
  25. Replies
    10
    Views
    1,379

    I just ordered from Spectrum Supply - way cheaper...

    I just ordered from Spectrum Supply - way cheaper than BandSawBladesDirect.
Results 1 to 25 of 208
Page 1 of 9 1 2 3 4