Search:

Type: Posts; User: Byron Trantham; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 8 minute(s) ago.

  1. Ok, here goes... I have a company rebuild my...

    Ok, here goes...
    I have a company rebuild my batteries (NiCads). When I first started working with them, I aksed about charging - leaving them in an active charger. Here is what they told me. ...
  2. I use PVC sewer pipe and it's associated...

    I use PVC sewer pipe and it's associated fittings. A suggestion - do not use 90 dergree fittings. Make a 90 degree by glueing two 45's with about 4" of separation - a nice smooth 90. I don't...
  3. Replies
    23
    Views
    12,366

    Scott, I ran into the same problem about a year...

    Scott,
    I ran into the same problem about a year ago. I had no idea my square wasn't! I used a technique posted here and found out it was waaaay out of square! I bent it into a accordion and...
  4. Can we say say "Think ouside the box?!" Good...

    Can we say say "Think ouside the box?!" Good one...
  5. Replies
    2
    Views
    879

    ZCI repair/re-use

    This may not be new news but I figured out a way to reclaim a zero clearance insert - two part epoxy! I have a walnut insert for my table saw that I made a while ago and the slot is getting too...
  6. Replies
    54
    Views
    11,960

    +2, except I got mine free from my...

    +2, except I got mine free from my brother-in-law! :-)
  7. Replies
    11
    Views
    7,687

    +999 for the gluebot! :-)

    +999 for the gluebot! :-)
  8. Replies
    5
    Views
    3,203

    Tung Oil Finish?

    I have a client that wants me to finish his Red Oak project with Tung Oil only. He has a bar that is finished with tung oil and re-applies it every few months. I bought some Formsby's today and see...
  9. Replies
    11
    Views
    2,859

    Need planer

    I currently have a DeWalt 735. I've had it since they were first released. A ton of wood has been sent through that machine. Sprockets broke which i have found out is not that uncommon. I was...
  10. Replies
    5
    Views
    1,480

    I've used it a lot. I bought in 2002 from...

    I've used it a lot. I bought in 2002 from woodpeckers with their PRL. Can't complain I guess.:D
  11. Replies
    1
    Views
    959

    Crown Settings

    I used to have a list of angles to cut crown laying flat rather than vertical. I have been asked to cut 7" crown. My 12" Dewalt won't do it vertically so I have to do it laying down. What are the...
  12. Replies
    5
    Views
    1,480

    PC 7518 bearings?

    I have a 7518 and the bearings are going out. Can they be replaced by me or would I have to "send it in"? Is it worth the repair? A new motor is $300!

    Any help will be appreciated.
  13. Replies
    9
    Views
    6,166

    3x paper

    FINALLY a definitive answer. I had gone to their site but obviously didn't get to where I needed to be. I too, have been using 3x for years with WB finishes. I have had occasional problems that I...
  14. Replies
    9
    Views
    6,166

    Stearated Sand paper

    Does anyone know if Norton 3X permium aluminum oxide sand paper is stearated? I can't seem to get an answer on this. Thanks.
  15. Replies
    17
    Views
    2,126

    Sounds like I did the right thing. Thanks for...

    Sounds like I did the right thing. Thanks for the input.
  16. Replies
    17
    Views
    2,126

    Filling a HOT gas genertor

    I had to use my generator last night - we lost power. Ran into a situation for the first time - had to refill the tank and the sucker was hot! What I ended up doing was putting a wet towel over the...
  17. Replies
    21
    Views
    2,632

    I bought DeWalt's 12" SCMS when it first came out...

    I bought DeWalt's 12" SCMS when it first came out (5-6+ years ago?). Still running strong. ;)
  18. Replies
    12
    Views
    7,855

    John, I made mine from two thicknesses of MDF,...

    John,
    I made mine from two thicknesses of MDF, Formica and Oak (trim). The table supports a Woodpecker's PRL, a PC 3 1/2 HP router and an Incra Twin Linear fence system. It's been in use 10-15...
  19. Replies
    2
    Views
    884

    If all four legs will fit on your table saw,...

    If all four legs will fit on your table saw, place the table on the surface and rock the table to determine which legs are taller. Using spray adhesive or double back stick tape, attach some 80 grit...
  20. Replies
    19
    Views
    3,585

    I sharpen mine (13" throw-aways) with a Tormek...

    I sharpen mine (13" throw-aways) with a Tormek system. The first time I did it (it was a pain to learn) I checked them against a new set of blades from DeWalt, mine were significantly more sharp. ...
  21. Replies
    16
    Views
    2,197

    I've had a Jet 6" for over 10 years. Have I...

    I've had a Jet 6" for over 10 years. Have I wished I had an 8"? Yea, but after I get the 8" I will wish a had a 12",.....! Where I buy my rough cut they can prep the wood to S3S (surface three...
  22. Replies
    6
    Views
    1,089

    +1 for CutListPlus

    +1 for CutListPlus
  23. Replies
    39
    Views
    5,981

    You can't begin to compare sewing costs to...

    You can't begin to compare sewing costs to woodworking! My wife, too, sews and embroiders. We added up "our hardware". Mine came to about $6K, hers - $28K!!! :o Now add in her very speicalized...
  24. Replies
    13
    Views
    5,766

    OK Guys, I get the message. My experience is...

    OK Guys,
    I get the message. My experience is normal. In this case the best solution is take to very small cuts with the router. Thanks for your input and help.
  25. Replies
    13
    Views
    5,766

    Milling Mahogany

    I have been milling - routing mahogany for the last couple weeks and have encountered a problem I can't seem to deal with. The grain will "tear out" here and there. When I say tear out, I mean...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4