Search:

Type: Posts; User: Mike Marcade; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    36
    Views
    3,517

    I was living in Southwestern Michigan at the...

    I was living in Southwestern Michigan at the time. There was one family in the neighborhood that was making grocery runs on snowmobile for people that needed food.
  2. Replies
    4
    Views
    1,135

    Personally I would use gasoline and matches, but...

    Personally I would use gasoline and matches, but thats just my opinion. I'm not a big fan of the knotty pine look. Please don't take any offense. ;)
  3. Replies
    9
    Views
    14,952

    Maybe "Ceiling" instead of "Roof" might clear it...

    Maybe "Ceiling" instead of "Roof" might clear it up some, unless I am misunderstanding. :D
  4. http://www.dewalt.com//ProductImages/PC_Graphics/P...

    http://www.dewalt.com//ProductImages/PC_Graphics/PHOTOS/DEWALT/TOOLS/LARGE/7/DW735_A3.jpg
  5. Replies
    28
    Views
    4,943

    I actually looked at your pics and then designed...

    I actually looked at your pics and then designed my setup on Pro/Engineer. Just PM me if you need some jointer help.
  6. Here is a link to the instructions if anyone...

    Here is a link to the instructions if anyone needs it:

    http://www.sawcenter.com/splitter.htm

    Also those mounting holes in the splitter are oversize so you can adjust the angle for your saw....
  7. Replies
    8
    Views
    70,256

    You don't really need any more pressure than your...

    You don't really need any more pressure than your tire requires. Just set your regulator at a little more than your tire needs than inflate it. Just check it with a reliable tire gauge.
  8. Replies
    28
    Views
    4,943

    Mine took me a couple of months to get completely...

    Mine took me a couple of months to get completely running too. :o also BTW I am leveraging your Board Buddy mounting design for my tablesaw fence.
  9. Replies
    28
    Views
    4,943

    Rob, You loosen the bolts to adjust the...

    Rob,

    You loosen the bolts to adjust the motor, then apply the spreaders to put the correct tension on the belt, then tighten the bolts and remove the clamps.
  10. Replies
    7
    Views
    893

    Why not just use Loctite?

    Why not just use Loctite?
  11. Replies
    4
    Views
    719

    One thing I noticed on mine is that if the screw...

    One thing I noticed on mine is that if the screw in the side of the insert is not adjust just right, it will put the blade in a bind. I usually don't make the insert so tight in its recess because...
  12. Replies
    28
    Views
    4,943

    I did the same thing. With perfect belt aligment...

    I did the same thing. With perfect belt aligment and really good tension using some of those one handed spreader clamps mine makes no bang or rubbing whatsoever, even with a link belt on. I can...
  13. Replies
    14
    Views
    3,565

    Naw ... thats just from a Texas Live Oak, and...

    Naw ... thats just from a Texas Live Oak, and from the looks of it, it must be just a sapling. :D:D:D
  14. Replies
    4
    Views
    1,525

    I got one of the Swanson T-bevels you talked...

    I got one of the Swanson T-bevels you talked about from Lowes. It looks decent to me, although there seems to be some straightness variance in the blade (nothing major though).
  15. Replies
    17
    Views
    4,734

    http://www.homedepot.com/catalog/productImage/ae11...

    http://www.homedepot.com/catalog/productImage/ae110089-6e4e-435c-a786-e7e7dca265fa_300.jpg

    :D:D:D
  16. Replies
    23
    Views
    12,735

    I clamp a straight edge onto the piece and run...

    I clamp a straight edge onto the piece and run the router along it to get my first true edge. Then I use that edge I just cut and run that along my table saw fence to get a parallel straight edge. ...
  17. Replies
    14
    Views
    12,748

    Around the area where I live, you may not be able...

    Around the area where I live, you may not be able to find one that speaks english. :mad:
  18. Replies
    13
    Views
    2,246

    Stay off of the runway. :D:D:D

    Stay off of the runway. :D:D:D
  19. Replies
    2
    Views
    7,720

    http://www.dewaltservicenet.com/documents/English/...

    http://www.dewaltservicenet.com/documents/English/Instruction%20Manual/631838-00,DW735.pdf
  20. Feel free to check out my Grizzly Customer...

    Feel free to check out my Grizzly Customer Service experience here:

    http://www.sawmillcreek.org/showthread.php?t=72962


    I have nothing but GOOD things to say about them. :):):)
  21. Replies
    7
    Views
    1,609

    I got some from Mcmaster-Carr

    I got some from Mcmaster-Carr
  22. Replies
    6
    Views
    1,028

    You can get a new charger from...

    You can get a new charger from Dewaltservicenet.com.
  23. Replies
    22
    Views
    2,389

    Do you mean the set screws used for adjusting the...

    Do you mean the set screws used for adjusting the eccentric bushings?

    BTW ... the tiles are not available in the Sam's club stores, you have to buy them online. See the links here:

    Tiles:...
  24. Replies
    5
    Views
    7,624

    Here are the parts lists for both models. The...

    Here are the parts lists for both models. The major difference I see is the C33H-12-4R has a satin chrome blade, that is what the C denotes before the part number.

    Catalog No : 11H-12-4RProduct :...
  25. Can't you adjust the angle of the motor to match...

    Can't you adjust the angle of the motor to match the angle of the drive pulley. I know that the belt would not be straight up and down but the pulleys would be aligned.

    You can also slightly...
Results 1 to 25 of 355
Page 1 of 15 1 2 3 4