Search:

Type: Posts; User: Larry Crim; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    1,146

    By the way if you do decide to make the...

    By the way if you do decide to make the adjustment make sure you mark the current position of the eccentric bushings before you loosen the setscrews so you can always get back to where you started....
  2. Replies
    3
    Views
    1,146

    John if I am reading you right you are saying the...

    John if I am reading you right you are saying the infeed table is higher on the side away from the fence, if that is true I would check the infeed compared to the outfeed before I adjusted anything. ...
  3. Replies
    10
    Views
    2,707

    Brian not sure about the wiring, but If you get...

    Brian not sure about the wiring, but If you get the grizzly switch be aware the case cover screws are plastic and you must be easy on them or they will break.
  4. Replies
    9
    Views
    1,251

    one of the best things I have bought for my WW...

    one of the best things I have bought for my WW hobby. I find I use it sometimes even when I don't need it just to stay cool.
    Larry
  5. Replies
    18
    Views
    2,902

    I have JET and Bessey I vote for the JET's larry

    I have JET and Bessey I vote for the JET's
    larry
  6. Replies
    36
    Views
    5,840

    Just AWESOME Carroll, that will be a project that...

    Just AWESOME Carroll, that will be a project that you will be proud of every time you place a piece of wood on it.
    Larry
  7. Thread: Allwood?

    by Larry Crim
    Replies
    10
    Views
    3,346

    Maybe it was short for alder wood, never seen...

    Maybe it was short for alder wood, never seen anything called allwood.
    Larry
  8. Thread: Leigh FMT

    by Larry Crim
    Replies
    3
    Views
    791

    Yes, but do not switch sizes or change anything...

    Yes, but do not switch sizes or change anything that that will require you to change the forward to back setting on the top, this is only critical if you are doing a the two joining boards have a...
  9. Replies
    7
    Views
    856

    via previous post I used oil based clear on the...

    via previous post I used oil based clear on the interior of a cherry chest that has some cedar lining. The clear on the under side of the lid went tacky and I have removed it and am refinishing it...
  10. Replies
    7
    Views
    856

    OIL/Water Clear finish

    Just a question can I apply water based clear coat over oil based clear? both GF clear
    Thanks
    Larry
  11. Replies
    4
    Views
    855

    Thanks guys that's why I love this forum, Live...

    Thanks guys that's why I love this forum, Live and learn, could have been worse at least it's only the underside of the lid. Finishing has always been my week side with WW.
    larry
  12. Replies
    4
    Views
    855

    Is the cedar ruining my finish?

    I built a blanket chest a few months back and lined it with cedar, the kind you get at lowes for closets and such. I finished the cherry with BLO and then about 4 to 5 coats general clear oil finish....
  13. Replies
    12
    Views
    4,010

    No I think you are right that is a bit high I...

    No I think you are right that is a bit high I would expect to pay the $5 for a bf and even that would be a little high for my area.
    Larry
  14. Replies
    5
    Views
    1,285

    Yes it will I have one and it fits fine larry

    Yes it will
    I have one and it fits fine
    larry
  15. Last one I made had 7/8 x 5 3/4 slats and it was...

    Last one I made had 7/8 x 5 3/4 slats and it was still solid as a rock I think you will be fine, I agree with the center leg unless you were to use a lot of slats, I used 12 slats 1" wide by 3/4 "...
  16. Thread: Clamp Rack

    by Larry Crim
    Replies
    31
    Views
    30,134

    Very cool, when are you taking orders? lol Larry

    Very cool, when are you taking orders? lol
    Larry
  17. Replies
    5
    Views
    2,040

    I'd like to help but I need a visual do you have...

    I'd like to help but I need a visual do you have anything on paper yet that could give us a better idea of the direction you are going?
    larry
  18. Replies
    7
    Views
    1,093

    Luke don't forget the garage sales I find a lot...

    Luke don't forget the garage sales I find a lot of good deals early in the morning in the memphis area for hand planes, chisels and have seen plenty on routers. Also there has been a couple of 14"...
  19. Replies
    125
    Views
    17,566

    The mistake was made by sears, if they cought the...

    The mistake was made by sears, if they cought the problem and corrected it then good for them but they should honor any purchases that came before they corrected it. I got one but when I went to the...
  20. Replies
    125
    Views
    17,566

    Thanks russ I got mine, when I went to the store...

    Thanks russ I got mine, when I went to the store they actually had a tag on the DP for 179 but when they rang it up it came up 479.00 they called the mgr to correct and he said it was a interner...
  21. Replies
    5
    Views
    1,719

    This was my original thought also but then got to...

    This was my original thought also but then got to thinking there must be some sort of hinge that would lift and offset also.
    Larry
  22. Replies
    5
    Views
    1,719

    Blanket chest hinge help

    Ok so am I the first person that has built something without thinking about the hinge placment first? Hope not.
    Here is the question I Have a simple chest with squared legs and panels in between, I...
  23. Replies
    21
    Views
    2,745

    That is just awesome you should be proud good...

    That is just awesome you should be proud good save.
    Larry
  24. Replies
    13
    Views
    4,941

    If it's big enough I use a band clamp but...

    If it's big enough I use a band clamp but depending on the size and shape I also use tape probably more than I use the band clamps.
    Larry
  25. Replies
    1
    Views
    647

    glad it helped I know when mine was out I didn't...

    glad it helped I know when mine was out I didn't even want to use it because it was so aggravating but when It was fixed I couldn't wait to get out in the shop and start jointing boards.
    larry
Results 1 to 25 of 286
Page 1 of 12 1 2 3 4