Search:

Type: Posts; User: Steve Dewey; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    1,082

    For eats, go to the "North End" for out of this...

    For eats, go to the "North End" for out of this world Italian - almost any of the places are a good choice - ask the concierge for a recommendation.

    For BoSox tix - good luck - and bring $$$$$ ...
  2. Replies
    6
    Views
    1,551

    That would be correct. But, I've gotta ask -...

    That would be correct.

    But, I've gotta ask - why thin kerf on a cabinet saw? I have the 5HP version and more than enough power to run full kerf. From my experience I'd say the 3HP version would...
  3. Thanks guys - looking at the set tonight it is a...

    Thanks guys - looking at the set tonight it is a "spacer" as Peter described not a bearing or rub collar. My method for coping is to set the "input" side of the fence in the same plane as the spacer...
  4. Shaper Rail & Stile set - bearing ("imports") vs. no bearing (Freud)???

    The only set I've used so far had a bearing for the rail end cut - like this one

    http://pricecutter.com/3-in-1-combination-cabinet-door-sets/p/285-8570/ I have the 15* bevel set from here. ...
  5. If you truly want to cut cycle time, you need to...

    If you truly want to cut cycle time, you need to think in terms of lean manufacturing where the goal is single piece flow vs. batch processing. Then you can identify which step is the constraint in...
  6. Replies
    23
    Views
    1,717

    Trust your "mistrust" - Mike Henderson offered...

    Trust your "mistrust" - Mike Henderson offered the best advice. Typically the benefit (payout) is discounted 10-15%. Use the funds in your 401k and 403b to make up the difference (or sell some of...
  7. If you're going to transfer to your pickup you...

    If you're going to transfer to your pickup you might as well pick it up at the local freight terminal - saves a 1/2 day of waiting around for the driver to show up. Plus they will load you with the...
  8. Replies
    4
    Views
    8,372

    Stuck Chuck - Makita 18V keyless

    My chuck is stuck - need help. It has a bit in it right now & I can 't get it to loosen. I tried to "cheat" using a clamp for leverage, but it deflects the plastic & still no go.

    Drill is 6...
  9. Replies
    39
    Views
    11,248

    I have ridgid 6" - it works fine, but I'm limited...

    I have ridgid 6" - it works fine, but I'm limited by the capacity. I just bought a Hammer 12" jointer/planer at almost 10X the price. Too bad you aren't closer, I'd make you a good deal on the...
  10. Anybody else wish NYW & TOH episodes were on itunes?

    Doing some research on plans for bunk beds. Browsing thru New Yankee workshop website I came on a revelation... I'm not willing to spend $25 for them to send me a DVD (they are phasing out VHS) and...
  11. Replies
    19
    Views
    6,461

    Basic machine is on sale for $3,000 (MSRP $3,500)...

    Basic machine is on sale for $3,000 (MSRP $3,500) plus shipping ($429 to residential Mass address). Price is going up 10% come April 1st.
  12. Replies
    19
    Views
    6,461

    Don - just read your thread - they asked me how...

    Don - just read your thread - they asked me how far Hartford was while I was ordering on the phone, then said nevermind, it's sold already - must have been you:rolleyes:. Great deal for you to save...
  13. Good news Don - If you need a fix earlier - send...

    Good news Don - If you need a fix earlier - send me a PM I'll put you to work... They are shipping mine in a week (I'll be on a ski trip next week) so I can meet the driver when I get back....
  14. Placed the order this morning for the Hammer...

    Placed the order this morning for the Hammer A3-31 plus goodies (extension table, "digital" dial, mobile base & extra blades). Prices are going up 10% on April 1 in case anyone else is on the fence....
  15. Matthew - just saw your post - thanks for the...

    Matthew - just saw your post - thanks for the feedback & the invite. As I mentioned above, I'm hoping to check out the exact model.
  16. Spoke to Felder today - Current Pricing on Hammer...

    Spoke to Felder today - Current Pricing on Hammer A3 31 is $3,000 plus shipping ($380 to Mass - seems high but diesel is $4 a gallon). They are expecting a price increase ~10% April 1st due to high...
  17. Replies
    30
    Views
    3,561

    Can you flip the cutter over & run in reverse?

    Can you flip the cutter over & run in reverse?
  18. This is a great thread - thanks guys For...

    This is a great thread - thanks guys

    For completeness a couple links to articles referenced above

    The FWW article that reviews the Euro machines
    ...
  19. That's what I want to hear - though I suppose a...

    That's what I want to hear - though I suppose a wixey DRO would accomplish the same thing...
  20. I realize that I'll be cranking away :o - I want...

    I realize that I'll be cranking away :o - I want to know if I can get back to 3/4" repeatably - Ie - is the scale accurate? - is there alot backlash in the system requiring me to approach from the...
  21. Thanks Jim just the kind of feedback I'm looking...

    Thanks Jim just the kind of feedback I'm looking for. After I posted this thread I saw your thread on the visit with Curt.

    The ratchet studs & knobs are a perfect example of a design that works...
  22. 12" jointer planer jet / grizzly vs. minmax, hammer, laguna HELP!

    Spent a couple hours yesterday searching sawmill & internet to find the answer, but am probably more confused than when I started...

    Looking to upgrade to a bigger jointer (currently have a 6"...
  23. Get the 2 tool set. Makita offers a "lightweight"...

    Get the 2 tool set. Makita offers a "lightweight" kit with 2 bats, drill & driver for ~$220 street. Also have the regular for ~$300. Biggest difference is the regular has larger battery (3 vs. 1.5...
  24. Replies
    5
    Views
    1,703

    I've had good luck with the mini porter cable...

    I've had good luck with the mini porter cable belt hooked up to my festool vac. (used the PC hose). Good excuse to pick up the "mini" dust extractor.
  25. homeshopmachinest is much more friendly to...

    homeshopmachinest is much more friendly to hobbiests than practical machinist. Hobart weld talk is the place for welding questions. None are as cordial as sawmill, but are informative.

    There are...
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4