Ok, I'm back up and running. New mother board installed..It was so easy to replace ( Less than a minute). The total cost was $1786.79. The tech had quoted me $1k too much. It's still pricey but...
Type: Posts; User: David Linahan; Keyword(s):
Ok, I'm back up and running. New mother board installed..It was so easy to replace ( Less than a minute). The total cost was $1786.79. The tech had quoted me $1k too much. It's still pricey but...
There was no lightning strike and the machine was turned off at the wall socket... I contacted the dealer I bought it from and they are also the official Australian Epilog agent/importer.
I think I might be looking around to see if I can possibly get it repaired. I'm a bit disappointed that I haven't had a follow up phone call or email from the distributor. I sent an email stating I...
Well I'm not a happy camper at the moment. I've owned a Zing 24 50W for a bit over two years and have just suffered a dead motherboard. It worked fine on the Sunday, I used it for about an hour. On...
A friend has bought his young son a black ukulele for his next birthday. He has asked if I would be able to engrave his name onto it. My concern is that it is a plywood construction and is finished...
I have the opposite problem. My laser is in the back shed and cold isn't a problem at all...even in the winter. But, come the warmer weather and nearly every day is over 30C, which according to the...
I have a 50W Zing 24 which I'm fairly happy with. My biggest "gripe" I think would be its "air curtain" air assist system. Because it feeds air into the workspace along a tube that runs the width of...
Sorry I'm so late getting back to this. I tend to think the problem was something like Mike Chance has suggested. My skills with Corel can only improve, so there is every chance the graphic has an...
Well, not long after I posted my question I worked out a way of getting the result I wanted. I converted my design to a bitmap, then outline traced it as line art. Then I ungrouped / boundary/...
Hi,
My problem is, I've created a design that I want to place a cut line around. It's a trophy that is for a car club I'm in and they will need about 20 of them. The thing is, when I try...
Well...I don't know what to say...I reconnected the first laptop running the 32 bit Win7, reset all the settings etc again.....and...yep...it worked!...I'm at a loss as to what I did or didn't do...
I connected another laptop to the laser with no success either. This unit runs the 64 bit version of Win7. So I installed the 64 bit driver etc etc...but there is still no reaction from the...
Yep Mike....I've done that a few times as well.......
I've tried that many times and again after your suggestion....but it still wont work.........:confused:
Unfortunately the laptop I use to run my Zing 24 50W had a hiccup and I needed to reset everything back to it's original defaults.( not happy). I reinstalled Corel x6, Photoshop CS3 , Norton...
I too had problems with the object slipping on the rollers...In my case I was engraving some glass beer mugs that had a heavy handle on one side.All went well for the first few but after a while they...
I kinda thought that the air assist curtain on the Zing isn't that good. I might try to rig up an air nozzle directly to an outside compressor. Mike's experience with a closer air stream could solve...
Hi,
I'm still learning with my new 50w Zing 24. A question I do have is about the air assist. I find that using it can cause the residue to be blown down onto the project which often leaves a...
Thanks for the help guys...I like the idea of the polyester film. I presume that after cutting I would need to get the wife out into my shed to peel off the masking paper....not too sure about...
Hi, I'm new to both this forum and using a laser. I'm quite enjoying both at the moment, although the laser causes a few wrinkled brows at times. I've tried searching for an answer to my...