Search:

Type: Posts; User: Bob Vavricka; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    0
    Views
    354

    FS: Nova Mini Cole Jaws

    I got these with some other used lathe accessories I bought and I don't have a Nova Chuck. They have a model number of CA6004 and I see Nova Mini Cole jaws with a model no. of 6006 online. I don't...
  2. Replies
    34
    Views
    3,036

    I'm confused. You said the gouge measures .515...

    I'm confused. You said the gouge measures .515 and think a 7/16 (.437) bit will work. Do you mean a 9/16 bit?
  3. Replies
    12
    Views
    2,049

    Thanks for the replies, I decided to buy the...

    Thanks for the replies, I decided to buy the AM6008/1QTHVLP package off the Homestead Page. They also have an Ebay page and it looked like the same setup was a little more from Ebay. I did call and...
  4. Minwax makes an ultra-flat version of their...

    Minwax makes an ultra-flat version of their Polycrylic Finish.
  5. Replies
    12
    Views
    2,049

    conversion spray gun recommendation

    Give me your recommendation for a conversion spray gun that will be used primarily for waterborne finishes. I have a 60-gallon 5hp compressor that is rated at 18.1 CFM @ 90 psi. I would also like to...
  6. Replies
    9
    Views
    1,505

    Penn State industries has some salt peppermill...

    Penn State industries has some salt peppermill kits that use what they call a jam chuck like you described. They have one that is 1" that will probably expand to what you need. 1in Jam chuck for Mini...
  7. Replies
    11
    Views
    1,380

    103 F in Oklahoma today and tomorrow. Projected...

    103 F in Oklahoma today and tomorrow. Projected low 80 F.
    I guess going to Tokyo wouldn't help me cool off.
    Bob V.
  8. Replies
    2
    Views
    1,092

    Found what I was looking for. It is called a...

    Found what I was looking for. It is called a Turmkreisel or tower top.
    Thanks
  9. Replies
    2
    Views
    1,092

    Can't remember the name of this top

    I made this top that spins on a pedestal and catches on the rim instead of falling off when it stops spinning. It has a name, but I can't remember it or find it searching for types of tops. I believe...
  10. Replies
    13
    Views
    3,187

    I pre-painted the OSB I put up in my shop. I put...

    I pre-painted the OSB I put up in my shop. I put a coat of oil based primer on (KILZ) the coated with the latex paint. I liked the results. I needed a small piece to finish the job and just coated it...
  11. Replies
    2
    Views
    2,011

    Thanks Robert, I couldn't duplicate what you...

    Thanks Robert, I couldn't duplicate what you said, but with that information I was able to find out how to put a hairline around the outline of the text and delete the fill. Thanks for pointing me...
  12. Replies
    2
    Views
    2,011

    laser cut Stencil letters

    I am a hobbyist and have a used 40 watt Epilog Mini laser for my own use mostly. I have been asked to make some stencils out of mylar that are mostly text. I have a font called Balton Stencil that...
  13. No, the softener is not recharging at the time...

    No, the softener is not recharging at the time this happens. I believe you are right that the bouncing pressure creates the noise at the head. If it wasn't for the noise at the head I wouldn't even...
  14. The water softener doesn't have any water coming...

    The water softener doesn't have any water coming out of the drain tube except during regeneration. The head information says it should be put in a system with over 125psi and the old head I replace...
  15. House was probably built in the 60's. There is no...

    House was probably built in the 60's. There is no pressure regulator. In the 32 years I have lived here, I have replaced/modified probably 80-90% of the water lines. Originally copper under the...
  16. Bill, I know the water pressure is high, but...

    Bill,
    I know the water pressure is high, but it's been that way for 33 years and the noise just started.
    A pressure regulator is a good idea.
    It is City water. No hammer arrestors in the house. ...
  17. Plumbing: water pressure and noise mystery

    I have plumbing mystery and I am posting this knowing the great amount of expertise in this community.

    I have a water softener and it started making an intermittent noise a month or so ago. I...
  18. Replies
    5
    Views
    822

    Looking at your first picture, it appears the pin...

    Looking at your first picture, it appears the pin on the one on the left in the picture is rotated and the part that rotates it is pulled out to the left. I think if it is put back in the position of...
  19. Replies
    8
    Views
    2,266

    It has been a long time since I worked on a...

    It has been a long time since I worked on a Powermatic 90 lathe. But if I remember correctly the belt was fairly wide and I wonder if you will find a suitable link belt to work with it.
  20. Replies
    31
    Views
    3,324

    Looks like fir plywood to me

    Looks like fir plywood to me
  21. Replies
    15
    Views
    3,812

    Turner was Bill Grumbine and looks like he was a...

    Turner was Bill Grumbine and looks like he was a member of this forum. See this thread Faceplate turning (sawmillcreek.org)
  22. Replies
    15
    Views
    3,812

    Years ago when I was first looking into turning...

    Years ago when I was first looking into turning bowls, I bought a video of a (I believe) Canadian woodturner who used hotmelt glue to hold his blanks to a waste block. He melted the glue in an old...
  23. Replies
    40
    Views
    4,983

    For a quick less messy "temporary fix" I would...

    For a quick less messy "temporary fix" I would find some heavy rubber sheet and wrap around the pipe and use hose clamps to hold it in place. What is the diameter of this pipe and how large of a hole...
  24. Replies
    15
    Views
    3,613

    Turn the handwheel to retract the quill and see...

    Turn the handwheel to retract the quill and see if that will eject it. If not put some pressure extra pressure on the handwheel and give a good rap with a soft blow mallet. Also check to see if the...
  25. Looking at the manual it appears there is a...

    Looking at the manual it appears there is a manual feed door above the paper tray. Open and close it to make sure it isn't keeping you from printing.
Results 1 to 25 of 444
Page 1 of 18 1 2 3 4