I use a version of this one
http://www.amazon.com/POWERTEC-70130-Collection-Fittings-Reducer/dp/B00LPOUW2Q/ref=sr_1_21?ie=UTF8&qid=1447893349&sr=8-21&keywords=vac+hose
but I bought it at...
Type: Posts; User: Roger Rayburn; Keyword(s):
I use a version of this one
http://www.amazon.com/POWERTEC-70130-Collection-Fittings-Reducer/dp/B00LPOUW2Q/ref=sr_1_21?ie=UTF8&qid=1447893349&sr=8-21&keywords=vac+hose
but I bought it at...
Guy on LumberJocks built one. See thread 95246.
Stumpy Nubs did this as an exercise / experiment. Go to his site and watch the video. It's worth it.
On so many levels he Craftsman unit is superior to the IVAC / I-socket. AND it was less expensive. If I could find a couple more I'd buy them myself. That controller was one of the few things...
Your wobble description suggests to me that your dowel holes are perhaps a tiny bit too shallow, as Mark suggests, and therefore it is impossible to completely seat the edges to each other. This is...
Put the slab in a big garbage bag, seal it up and put it in the sun (preferably on a concrete slab to add some solar reflection) for a couple weeks to fry the buggers. You don't want any of them...
If I had to do it but only needed a few, I'd tackle it with rasps, files and sandpaper. You could probably knock out a half dozen in the time it would date to figure out a different method. Those...
Congratulations! Well done. This was the hard part. You should go buy yourself a new tool as a reward. I'm serious, you earned it.
I'm in the camp of mapping out the circuits. If you don't have a helper, pick up a Circuit Detective from Harbor Freight, for example, it will help you identify what is where. Importantly, test...
I definitely agree with the brick clips. I had some for several years and used them to hang signs and wreaths on the outside of the house and to hang some things on the fireplace inside. I passed...
Don't confuse "suction" with volume. I have an HF unit, I'm running 20 feet or so of 4" HVAC duct over to a planer with stops along the way at a Table Saw, sander, etc. I have blast gates, as it...
I bought an HTC mobile base for my Griz table saw when I got it. I was really happy with it so bought an adjustable base for my Buffalo Forge drill press. It has served me well and I have no...
I agree with Alan. A bead down the bottom of he groove will force some squeeze out into the sides of the groove when you clamp it closed. If you have a good fit that then swells a bit, good clamps...
I experienced the nut tightening until I included a washer below the nut. It's a different washer from the ones for the spindles because the shaft has to pass through the washer but it is a smaller...
Amazon still has a few in stock http://www.amazon.com/Ridgid-EB4424-Sander-Oscillating-Edge/dp/B0015B9G0S/ref=sr_1_1?ie=UTF8&qid=1382846032&sr=8-1&keywords=eb4424
I want to thank everyone for their analysis and their comments. It is absolutely everything I hoped for to have people who actually understand this stuff discuss it and arrive at data and...
I'm getting ready to move to a 4 inch piped (sheet metal snap lock) duct system with drops to replace my single duct moved machine to machine approach. Contemplating it, I have some challenges that...
I've had very good luck with these. http://www.homedepot.com/p/E-Z-Ancor-Twist-N-Lock-50-Drywall-Anchors-with-Screws-25-Pack-25200/100133106#.UbLFwh7nbIU They aren't expensive and they are...
My garage has an 11 foot ceiling. I built a rack that looks like a ladderer except the rungs are 2 foot long 1 1/4 inch dowels and they are only spaced about 6 inches apart. I hung it from the...
I personally like the ones Myk Rian shows the pic of. The real advantage for me is that they don't require high precision for initial positioning of the clamp "legs", and then they give me lots of...
I have a cheap dust collector but I upgraded the filter bag to an American Filter from Highland Woodworking that filters to 1 micron. Others go with a Wynn filter cartridge. I hang my Jet air...
Have not heard of it, what is it? Do you have a link?
Martha Stewart just called to tell me she hates you.
I started with the PC 890. I liked it and had all the flexibility I needed. I liked the above the table height changes and the above the table bit changes. But, I knew someday I'd want more...
I am having a difficult time comprehending the idea of reversing the motor rotation. It seems to me that reversing the rotation is counter productive unless you also reverse the "directionality" of...