Search:

Type: Posts; User: Dick Bringhurst; Keyword(s):

Page 1 of 17 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    352
    Views
    51,300

    Count me in. Dick B.

    Count me in. Dick B.
  2. Replies
    10
    Views
    1,923

    Last time I was in your spot I bought a trailer...

    Last time I was in your spot I bought a trailer hitch for my truck, rented a trailer (oneway) and delivered. Had a nice vacation (a short one) and gained a hitch. The cost was slightly less than...
  3. Interesting, Only one mention of PC. Dick B.

    Interesting, Only one mention of PC. Dick B.
  4. Count me in please. Digk B.

    Count me in please. Digk B.
  5. Please count me in. Dick B.

    Please count me in. Dick B.
  6. Count me in. Dick B.

    Count me in. Dick B.
  7. Replies
    35
    Views
    7,761

    I'm not disappointed. I say that's great. I'm...

    I'm not disappointed. I say that's great. I'm happy for you. As far as cutting the pieces yourself, the quality of the cut is more dependent on the blade you use and how you guide the saw. Get a...
  8. Replies
    35
    Views
    7,761

    It's been my experience the BLOG will not...

    It's been my experience the BLOG will not guarrentee accuracy. Also their blade leaves something to be desired. A hatchet would be better. Dick B.
  9. Replies
    8
    Views
    6,494

    V-2 is the the type I have.

    V-2 is the the type I have.
  10. Replies
    8
    Views
    6,494

    Robert, I don't think you can go wrong with the...

    Robert, I don't think you can go wrong with the PRL models. I first had a Jessem Rout-R-Lift. I didn't like it because of "lash" in the height adjusting system. I believe that has been corrected...
  11. Replies
    22
    Views
    6,906

    euro hinge

    the 35mm bit should NOT have a center spur, it can go all the way thru depending on the depth of the wood. Test on scrap. Dick B.
  12. Replies
    21
    Views
    3,540

    I used one for many years with acceptable...

    I used one for many years with acceptable results. The problem I had happen fairly frequently was the presure it took to raise the mortising chisel out of the mortise. A drill press is designed to...
  13. Replies
    5
    Views
    1,014

    I think that's the easiest solution if the...

    I think that's the easiest solution if the thickness you end up with is acceptable. Dick B.
  14. Toss my hat in the ring. Dick B.

    Toss my hat in the ring. Dick B.
  15. Replies
    15
    Views
    2,616

    The quickest way I've found to find where it...

    The quickest way I've found to find where it came from is to pick it up and throw it away. You will usually have your answer the day after your trash pick up.
  16. If you use either of these magnetic type setters...

    If you use either of these magnetic type setters and you have carbide blades make sure the magnets will work on carbide. I think it takes a rare earth magnet to work with carbide. Dick B.
  17. I don't own a 621 but it might be possible to put...

    I don't own a 621 but it might be possible to put a nut on the adjuster to act as a Jam Nut. Dick B.
  18. I just set up a roller stand on the output side. ...

    I just set up a roller stand on the output side. Dick B.
  19. You can buy cans of compressed air similar to a...

    You can buy cans of compressed air similar to a rattlle can of paint. I use it to blow out my computer periodicly. Dick B.
  20. Replies
    352
    Views
    62,196

    Count me in please. Dick B.

    Count me in please. Dick B.
  21. Replies
    35
    Views
    5,076

    Poll: Some #1 but mostly #3. All 20 amp. Dick B.

    Some #1 but mostly #3. All 20 amp. Dick B.
  22. Thanks Mr. Kerry. Count me in. Dick B.

    Thanks Mr. Kerry. Count me in. Dick B.
  23. Replies
    35
    Views
    8,428

    Bosch -- got three -- Love 'em. Dick B.

    Bosch -- got three -- Love 'em. Dick B.
  24. Replies
    23
    Views
    3,841

    The latest Delta jig can be adjusted for the...

    The latest Delta jig can be adjusted for the miter slot distance to the blade. Dick B.
  25. Replies
    5
    Views
    12,971

    OK I'll bite. For what application with crown...

    OK I'll bite. For what application with crown molding? Dick B.
Results 1 to 25 of 410
Page 1 of 17 1 2 3 4