Search:

Type: Posts; User: Jim Tabor; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    916

    I have the same Fuji Mini-Mite 5 except I have...

    I have the same Fuji Mini-Mite 5 except I have the T75G gravity gun. I also wanted a second gun for latex and was looking for something a little less expensive than a second T75G. After considerable ...
  2. Replies
    13
    Views
    2,034

    Phillip, Both of the nylon cups were leaking...

    Phillip,
    Both of the nylon cups were leaking material around the lid and running down the side of the cup. I also bought a 400cc aluminum cup, it also does not have a gasket. It leaked so bad that I...
  3. Replies
    13
    Views
    2,034

    I bought a Fuji Mini-Mite 5 with a T75G gravity...

    I bought a Fuji Mini-Mite 5 with a T75G gravity cup this past December. It's taken about four months to start to feel comfortable with it and learn the proper adjustments with different brands of...
  4. Thanks James, I've been considering the 3M PPS...

    Thanks James,
    I've been considering the 3M PPS system. In the meantime I ordered a second Fuji T75G without a cup and ordered a Apollo 8 oz. gravity cup. Just hope it will fit. Fuji cups range from...
  5. Thanks John, I didn't know about the WB ...

    Thanks John,
    I didn't know about the WB flatter, I keep that in mind. Jim
  6. Coat of USH3000 shellac sealer, Crystalac WB...

    Coat of USH3000 shellac sealer, Crystalac WB grain filer, second coat of USH3000 shellac sealer, three thin coats of EM6000 semi-gloss 6000 WB lacquer. Looks great, but I have a gallon of EM6000...
  7. According to Jeff the selection of products for...

    According to Jeff the selection of products for oak is fine. He couldn't comment on the Crystalac Grain Filler as he had not used any for several years. I did some test with the wood I plan to use...
  8. Replies
    4
    Views
    4,104

    That looks like two part epoxy to me. I use two...

    That looks like two part epoxy to me. I use two part all the time to cover cracks and knots. Most often with a little stain mixed in to make it match the darker area of the knot..
  9. Replies
    4
    Views
    1,397

    When I watch a video like that I wonder why HVLP...

    When I watch a video like that I wonder why HVLP systems don't have a pressure gauge. For example, if a Fuji 3 turbine produces 6.5 psi, a 4 turbine 8.0 psi, and a 5 turbine 9.5 psi, isn't it...
  10. I talked to Jeff Weiss about the USH3000 and...

    I talked to Jeff Weiss about the USH3000 and EM6000 and it's on the way. At the time I didn't plan on grain filler so it wasn't part of our conversation, I also didn't plan on oak at the time so all...
  11. So I called Crystalac and they said any WB...

    So I called Crystalac and they said any WB product should be okay but recommended I test it on scrap first. They also recommended the WB shellac (or WB sealer) first and then the filler.
  12. Thanks John, I didn't know that. I'm going to...

    Thanks John,
    I didn't know that. I'm going to call Crystalac now to find out. Jim
  13. Need Advice On Finishing Oak Project With Grain Filler and Target Coatings.

    I’m getting ready to start a chair project using oak. It will be finished with two coats of Target Coatings USH3000 shellac sealer and then3-4 coats of EM6000 lacquer.
    Most of my chair projects are...
  14. Well I've been in contact with Mike Smith of...

    Well I've been in contact with Mike Smith of HVLP TEK.com for the past couple of days seeking information and help on adding a second gun to my Fuji Mini-Mite System. He has gone out of his way to...
  15. Replies
    24
    Views
    5,861

    Yes, why not...I worked with school districts...

    Yes, why not...I worked with school districts back in the 80's and 90's and that's the way asbestos abatement enclosures were set up.
  16. Would like to add second gun to my Fuji Miti-Mate system, Recommendations?

    I’m looking to add a second spray gun to my fairly new Fuji Mini-Mite 5 system. It came with the T75G gun and gravity nylon cup that had to be switched to aluminum cups to stop cup/lid leaking. Does...
  17. Thanks Jamie, You solved my problem. I connected...

    Thanks Jamie,
    You solved my problem. I connected the turbine, removed the cap and found out the tube check valve was defective, wouldn't let air pass in either direction. I Replaced the check valve,...
  18. I'm going to send the gun to Fuji since it's only...

    I'm going to send the gun to Fuji since it's only two months old and let them check it out. It seems when I contact them I get conflicting information.
  19. John, Thanks for the feedback. I really think...

    John,
    Thanks for the feedback. I really think there is something wrong with my gun. I'm am using a #4 Ford cup and I have to thin so that the material flows through the cup in about 18-20 seconds. I...
  20. The problem is that I can't get anything out of...

    The problem is that I can't get anything out of the gun if I use less than a 1.5 needle and then it's just a mist. By going to a 1.8, thinning like 20% and opening the fluid control 3-4 turns I can...
  21. Problems Spraying Waterborne Finish With My New Fuji

    I bought a Fuji Mini-Mite 5 with a T75 gravity cup last December and I’m having a difficult time getting the adjustments correct.
    I’m using waterborne General Finishes Enduro-Var and Crystalac Top...
  22. Replies
    11
    Views
    1,276

    Went over to Springfield yesterday and replaced...

    Went over to Springfield yesterday and replaced the Grizzly G1023RL table saw I sold at auction four years ago. I moved from my farm in Missouri and sold everything as I thought I was done with...
  23. Replies
    18
    Views
    2,273

    What's with this weather change?

    Yesterday, last day of summer, 92 degrees, clear and daylight until 7:40 pm. Today, first day of fall, 61 degrees, raining and almost dark at 5:20pm.
  24. Replies
    5
    Views
    1,307

    Tom, Thanks for the additional information. A...

    Tom,
    Thanks for the additional information. A few years ago I used white on raw wood while making maloof style chairs. I used it in place of steel wool before the oil finish to more or less burnish...
  25. Replies
    5
    Views
    1,307

    Thanks John and Tom. I ordered a box of the white...

    Thanks John and Tom. I ordered a box of the white Scotchbrite pads from ebay today. Jim
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4