Search:

Type: Posts; User: stephen wood; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    1,145

    Thanks for the ideas. I bit the bullet and...

    Thanks for the ideas. I bit the bullet and bought a solution from McMaster-Carr.
  2. Replies
    9
    Views
    1,145

    Perfect! Thank you!

    Perfect! Thank you!
  3. Replies
    9
    Views
    1,145

    Short handle for TS blade angle

    This is used to turn the blade angle adjustment on my Rigid table Saw. I can’t use the stock handle since I added a router extension. Where can I buy a shorter version or how would I fabricate one?
  4. Replies
    4
    Views
    959

    support for table saw extension

    I'm looking to extend the functionality of my contractor table saw. I have an extra cast iron extension that I'd like to insert between the base table top and my router extension but this will put...
  5. Replies
    7
    Views
    1,125

    Thanks for the tips. I'm going to follow up on...

    Thanks for the tips. I'm going to follow up on the 2c-3c differences.
  6. Replies
    7
    Views
    1,125

    Minimax SC 2C pricing

    I'm considering the Minimax SC 2C but not quite ready to pull the trigger. On their site they say it's on sale (1k off list). Is this an everyday sale price or is it really a temporary sale?
  7. Replies
    2
    Views
    449

    Glue for flush trim door pull

    I'm installing new pocket doors and lost two of the 3/4 stainless steel escutcheon pins meant for installing the flush door pulls. Of course I cannot find replacements anywhere on the internet. The...
  8. I guess I was being too wimpy. I opened it up...

    I guess I was being too wimpy. I opened it up and sprayed a heavier coat. Thanks John.
  9. gloss finish with SW Emerald Urethane

    I'm spraying a bathroom cabinet with Sherwin-William Emerald Urethane Gloss. After 8 or so coats it's just not looking as glossy as I thought it would. I'm using an Apollo Eco-5 HVLP turbine. I've...
  10. Replies
    5
    Views
    994

    Thanks John!

    Thanks John!
  11. Replies
    5
    Views
    994

    Jim - Thank you for this and all the other sage...

    Jim - Thank you for this and all the other sage advice you've given me on my many questions! -Steve
  12. Replies
    5
    Views
    994

    Control dust before spraying

    I need to spray in the garage shop i just used to build a cabinet. I’ll be spraying either SW or BM paint. I know i can sweep/vacuum/clean but how long should i wait for the dust to settle? How much...
  13. Replies
    12
    Views
    1,653

    All great information. Thank you!

    All great information. Thank you!
  14. Replies
    8
    Views
    1,263

    I can use a plane as you suggest but just curious...

    I can use a plane as you suggest but just curious as to what’s the issue with sanding.
  15. Replies
    12
    Views
    1,653

    best paint for bathroom cabinet

    I'm painting the edge treatment on the euro style cabinet with a brush, but will probably spray the doors and drawer fronts with an HVLP setup. Any recommendations on brand/type of paint for this? ...
  16. Replies
    8
    Views
    1,263

    painting maple burned by saw blade

    I ripped some maple for plywood edge treatment and wound up with burn marks. Next time I'll take more care. Anyway the plan is to paint the edge treatment. Do I need to sand off the burn or will...
  17. Replies
    6
    Views
    834

    Slides for very wide drawer

    Designing a frameless bathroom vanity cabinet 39 inches wide. Want the top drawer to be the whole width and inside to wrap around the sink. Using under mount slides; one on each side. Will the...
  18. Replies
    10
    Views
    1,111

    No good reason. My only experience with...

    No good reason. My only experience with frameless has been using iron-on edge banding and I'm not so happy with that. I could use solid wood edging; so I'd just use wider stock for that on the...
  19. Replies
    10
    Views
    1,111

    rail and stile size on bathroom vanity

    I'm trying to maximize opening sizes so am looking for advice on minimizing rail and stile widths, and still have it look correct. I'll be looking to do full-overlay (doors in center, drawers on two...
  20. Replies
    8
    Views
    887

    Jim, Nice looking bench! Along with my regular...

    Jim, Nice looking bench! Along with my regular bench I also purchased the 1-rail option but never installed it. I was concerned that it would introduce instability. Since going without the...
  21. Replies
    8
    Views
    887

    Noden adjust-a-bench storage

    Looking for ideas on how best to utilize space under the bench.
  22. Two good solutions. One thing I omitted is that...

    Two good solutions. One thing I omitted is that there is a nut welded under the angle. In this case I needed to go the route Paul suggested. Here is the end solution that just needs to either...
  23. Issue with adjusting feet on workbench

    I'm ditching the casters on my Noden Adjust-A-Bench in favor of something more solid and more adjustable. I need to match the height of my table saw and i can't quite do it with the casters...
  24. Nice video. Thanks! I have the Keller jig but...

    Nice video. Thanks! I have the Keller jig but thinking of an upgrade.
  25. Replies
    9
    Views
    984

    LOL, I fully expect it to go that way!

    LOL, I fully expect it to go that way!
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4