Search:

I went the cheap route and bouth the 6" snap lock assembled it then used a reducer from the 8 to the 6"
working great.
One other thing I boought was 3 rolls of duct tape no not the grey or black...

Nice job on the bench , I should have loaned you my LN #8 plane that would he helped you square her up a little quicker
Great job
Bill

John,
Pick up a dvd from Chatsworth on sharpening, you will never be frustrated again
Bill

Congratulations
Bill

I switched from an older Griz type that duscharged to two "hula hoops" that I installed high efficience filters on , I went to a 3 hp super gorilla and noted a large change in the system and the...

did some checking and borrowed an accurate "within 1 degree " temp gage. the motor temp peaked at 134 degrees after about 45 minutes , ran it for another 1 hour 15 min and there was no change
So it...

Years ago I made my own power section by making a plywood outer box and going to grainger to get a small 3 stage turbine blower motor. I beleive this cost about $100.00. then I bought the hose and...

really appreciate this post, you have helped me a lot,
Greatly appreciate it
Bill

I will try it this morning and let you know
Bill

Unfortunately this is a sign of the times, more and more are closing
Here in Illinois there is a small number of shops left went to get some hard maple for some new vise jaws and the stock at the...

As previous stated have more circuts than less. I built my first shop and added circuts, then here at my second shop just doubled the plans and to date 5 years later its working well.
Just a...

What should a 3 hp motor temp be on an Oneida system?
Mine gets to 140 degrees in 30 minutes???????

Something is not right , yes will also be calling Oneida?? this is with the 15" impellar same...

They should make a GANG SAW with 12 blades then you can cover everything???????????

HAPPY APRIL 1ST

I have had 1/3 of the basement left unfinished for a workshop that is 40 x 15'. also the ceilings are 9'8" to the bottom of the floor joists. this has no celing in it and I like it that way. suggest...

First thanks for this post as it has helped me in my little issue.
I have taped all of the joints and the seams of the duction added 3 6" gates and now have the motor running cooler than ever.
My...

restore them for future use

The stanleys did the job but it took a while to get the desired result, the LN's are more accurate in setting and I have spent a long time preparing each of the blades to my satisfaction.8 to 10...

if you were to purchase any nice plane highly recommend that you get the DVD on sharpening them , I bought the David Charlesworth and thought I knew all there was to know .
I WAS WRONG it helped...

David this is the wynn kit on the Oneida and I do not know if it will fit the 2 hp or not, this one as you can see is mounted high for the clerance of the filters and dust pan.
the motor is 9' 8"...

David the old collector was about 10 years old worked well but it was used with a Blue tornado cyclone that I also sold.
This was a "cleaner " set up more efficient and more room left over
Bill

Rick and Tom

If, there was a dust collector running with an 8" opening "inlet" and there was a direct discharge with no restriction on the outlet also say 8"
if the motor was running hot "...

I beleive and willing to be corrected the issue is that with no discharge backpressure the rotor can "overspeed" and draw more than the required Amps in this condition.
most motors have an internal...

yes Good observation here is the car

http://i224.photobucket.com/albums/dd18/eightweight2/IMG_0134_0101.jpg

I had a 3 hp Dust collector " modified" and finally went to a Oneida pics below

From this
http://i224.photobucket.com/albums/dd18/eightweight2/IMG_1870.jpg

To this
...

I had some old planes and upgraded to 4 Lie Neilsen's the 60-1/2, 4-1/2, 5-1/2
and the #8

http://i224.photobucket.com/albums/dd18/eightweight2/IMG_0137_0098.jpg

to these
...

I just came to find a new Quincy QT-5 compressor for sale at close out its was 50% off of new
these are bigger than I was looking for with 175 psi rating and 17.2 CFM at 175 psi.
There one hell of...