Search:

Type: Posts; User: Mike Zilis; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    2,169

    She's a beauty! Well done and congrats on the new...

    She's a beauty! Well done and congrats on the new router system.
  2. Replies
    9
    Views
    2,355

    Hi Marty, Thanks for the great questions. ...

    Hi Marty,

    Thanks for the great questions.

    Size of air intake holes: I agree with your theory that the force of your dust collection should be considered in the size of the intakes. In my case,...
  3. Replies
    9
    Views
    2,355

    Charles & Dennis - Thanks guys. I had a long time...

    Charles & Dennis - Thanks guys. I had a long time to think about what I would have done differently. It's far from perfect but the evolution is in the right direction for me.

    Marty - Looking...
  4. Replies
    9
    Views
    2,355

    This first pic shows the back panels of the RT....

    This first pic shows the back panels of the RT. The top and bottom panels are removable. The middle section would need to be unscrewed from the case.

    281661

    With just the top panel removed I...
  5. Replies
    9
    Views
    2,355

    New Router Table Build Complete

    I finished this in the fall but only posted a few pics of the front. Here I'll go through some of the design ideas and provide some detailed photos.

    I built my first router table in 2007 when I...
  6. I've got the same collector. While I haven't had...

    I've got the same collector. While I haven't had any leakage I guess it's possible that the cloth covered spring ring could lose some of its spring tension after being compressed for a long time. I...
  7. Replies
    7
    Views
    1,555

    I was going to suggest mortising out space on...

    I was going to suggest mortising out space on both the top and the bottom for a flush fitting hardwood insert. This way you can get the screws to anchor at both ends while passing through a layer of...
  8. Replies
    2
    Views
    1,090

    You could possibly inlay a thin strip of UHMW...

    You could possibly inlay a thin strip of UHMW plastic on either half of the drawer slide (or both).

    Also, Lee Valley sells low friction tape that might work if you're up for some experimentation...
  9. Replies
    16
    Views
    16,882

    I switched to SPAX screws (Posi Drive)...

    I switched to SPAX screws (Posi Drive) exclusively a couple years ago now. I'm very pleased with them and the Posi bit is about the only driver I use these days.

    Mike
  10. Replies
    352
    Views
    51,370

    I'd like to be included in the drawing. Thanks!

    I'd like to be included in the drawing. Thanks!
  11. Same with my miter gauge to blade contact I had a...

    Same with my miter gauge to blade contact I had a while back. The cartridge did its job to stop the blade dead to rights. I was able to take the blade (Freud Thin Kerf Glue Line Rip) out of the...
  12. I'm not familiar with production screws. I've...

    I'm not familiar with production screws. I've been using SPAX for the last couple of years and really like them. I pre-drill using a tapered bit with a countersink. Works great.
  13. I'd like to be included. Thanks!

    I'd like to be included. Thanks!
  14. Please include me. Thanks!

    Please include me. Thanks!
  15. Please count me in. Thanks!

    Please count me in. Thanks!
  16. Please count me in. Thank you!

    Please count me in. Thank you!
  17. Another great give away! Thank you. Count me in.

    Another great give away! Thank you. Count me in.
  18. Replies
    872
    Views
    98,835

    Oneida makes great products! Please count me in.

    Oneida makes great products! Please count me in.
  19. Great product! Please count me in. Thanks ...

    Great product! Please count me in.

    Thanks

    Mike
  20. Jerry, just bring it by my place and run it...

    Jerry,

    just bring it by my place and run it over my 12" Jet Jointer/Planer Combo machine. Easy peasy lemon squeezy.

    Mike
  21. Replies
    1,035
    Views
    121,353

    Thank you to the forum and to Grizzly for this...

    Thank you to the forum and to Grizzly for this drawing! Please count me in.

    Mike
  22. I had thought that my table saw could do both...

    I had thought that my table saw could do both cross and rip cuts, but I find it much more efficient to dedicate my table saw for ripping and my Bosch 4410 for cross cut duty. In fact I'd like to sell...
  23. Replies
    6
    Views
    1,992

    Thanks, Jim! I was wondering how I could justify...

    Thanks, Jim! I was wondering how I could justify not washing my car all winter! (tongue planted firmly in cheek)
  24. Replies
    9
    Views
    5,578

    Jeff, Bill & Joshua, Your input is greatly...

    Jeff, Bill & Joshua,

    Your input is greatly appreciated. Whatever I end up replacing on my planes, I'll be keeping the original knobs, totes and hardware in case I need to bring them back to...
  25. Replies
    13
    Views
    3,495

    Awful nice work, Craig. I'm really partial to...

    Awful nice work, Craig. I'm really partial to quilted maple and love to see it in furniture like your table. I rarely see it for sale at my local hardwood supplier.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4