Search:

Type: Posts; User: Nick Mastropietro; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Big +1

    I have helical cutter heads in both my powermatic planer and jointer, rather economical when you consider that each cutter has four cutting surfaces - that's 4 complete change outs. With the right...
  2. Replies
    10
    Views
    1,270

    Mike's got it right, I don't think it matters, on...

    Mike's got it right, I don't think it matters, on oil to worry about.
  3. Replies
    10
    Views
    1,270

    My 2 cents

    Jack
    I purchased a Thomas 120v Wob-L oil less vacuum pump from e-bay 3.5-4 cfm and it works fine. As for the chucks, many here use either wood or PVC and seal the edge with fairly dense closed cell...
  4. Replies
    34
    Views
    5,539

    Out on a limb

    For those of us who have read the very informative thread and have learned a thing ot two about finishes but don't have a clue what the heck (Chatoyance) means:confused:, well thanks to...
  5. Replies
    15
    Views
    2,863

    John, in responce to your questions - Thoms got...

    John, in responce to your questions - Thoms got it right, It's primarily the handwheel.
  6. Replies
    15
    Views
    2,863

    Dave - Tim thanks for the responses and the good...

    Dave - Tim thanks for the responses and the good tip concernng the sealer. Yes I do have a morse taper to mount the chuck.
    Thanks again
  7. Replies
    15
    Views
    2,863

    One More Picture

    Spun up to about 800 rpm and holds great.
  8. Replies
    15
    Views
    2,863

    Another Vacuum Chuck

    I finally finished building my vacuum chuck, I got the Thomas pump from e-bay for $70.00 shipped, the rest of the hardware I bought from McMaster-Carr. It is approterate to give Steve Schlumpf the...
  9. Replies
    18
    Views
    2,237

    Stoppin in Ohio????

    Hey Bernie, my guess is you’re a bit overloaded and being the concerned citizen that I am, I suggest you stop by and unload some of that excess baggage ;);). I must admit, I'm a bit envious, sure...
  10. Replies
    7
    Views
    2,317

    I saw it too

    I came across this video about a year ago and immediately purchased the respirator and use it whenever power sanding. It's also a great platform for vapor cartridges when spraying finishes. I would...
  11. Replies
    9
    Views
    1,257

    Here are the pictures

    Maple with a salad bowl finish.
  12. Replies
    9
    Views
    1,257

    First Bowl

    I took a "Logs to Bowls" course at the local Woodcraft this Saturday and turned my first bowl.:D About 3/4 of the way through I got a catch and blew up the edge:mad:. Now I have candy dish:o Oh well...
  13. Replies
    14
    Views
    4,220

    Update

    Well it’s been just about a month since I discovered why my dust collector was tripping off for no apparent reason. The suction hose from the collector to the separator was lying against the control...
  14. Replies
    7
    Views
    1,913

    My Casters

    Mike, this is a link to a thread I posted showing the casters I purchased.
    http://sawmillcreek.org/showthread.php?t=134344

    This link shows some of the installation process...
  15. Replies
    18
    Views
    2,762

    John, now that your a moderator it's your...

    John, now that your a moderator it's your responsibility to help further your hobby and a great way to do that would be to share pieces of anything Robert might send you:D Ya I think it's written in...
  16. Replies
    17
    Views
    25,698

    I don't have enough room in my garage woodworking...

    I don't have enough room in my garage woodworking shop to have a traditional woodworkers bench, so I purposely looked for a Zyliss vise and I use it whenever a woodworking vise is needed. I know it...
  17. Replies
    35
    Views
    4,415

    Retainer

    I'll just say YES! Now am I going to have to pay for that legal advise or is this a part of your Moderator services?
  18. Replies
    35
    Views
    4,415

    Worse Then That

    Cathy if I would have bought 1 cent more I would have been required to sell the harley just to avoid a divorce, and THAT ain't happenin !
  19. Replies
    35
    Views
    4,415

    All is well, harmony has been restored to the...

    All is well, harmony has been restored to the vortex.
  20. Replies
    35
    Views
    4,415

    All Just Just Good Natured Fun

    Aaron, easy big guy this has all been just a back and forth good natured go around. John I sure hope you didn't misunderstand. If anybody else took my comments as anything more than jesting, I...
  21. Replies
    15
    Views
    2,159

    William, this looks like a Jet 10-14 Mini Lathe,...

    William, this looks like a Jet 10-14 Mini Lathe, Rockler is selling the current model for $350.00. This might not be a bad deal if the lathe is in good condition and is within your price range. My...
  22. Replies
    35
    Views
    4,415

    Redemption is good for the soul, not to mention the reputation

    Well John, I trust you completely when you say that pics with every gloat is the documented law. I'm not even going to ask you to provide a copy of the laws and regulation governing the ues of the...
  23. Replies
    35
    Views
    4,415

    Here's the Rest

    And the reciept too !!!
  24. Replies
    35
    Views
    4,415

    The Proof Is In

    I know I'm relatively new to the Creek, but when did we as civilized people stop giving one another the benefit of the doubt. Well never mind, In an effort to satisfy the doubters among you and to...
  25. Replies
    71
    Views
    7,453

    God is Life

    Joe, I have taken the time to read every post in this thread and have been overwhelmed by the magnitude of care and sympathy for you and your loved ones in light of your loss. No words that we have...
Results 1 to 25 of 175
Page 1 of 7 1 2 3 4