Search:

Type: Posts; User: Harvey Crouch; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    19
    Views
    4,677

    I tried, got a corner caught, and ended up with 8...

    I tried, got a corner caught, and ended up with 8 stiches. I will stick to a bowl scraper in the future.
  2. Replies
    7
    Views
    1,634

    Spalded Pecan Bowl

    The was the prettiest piece of wood I had seen for a long time. I hope I did it justice. 7" high; 11" wide All comments welcome.
  3. Replies
    12
    Views
    2,156

    Mesquite Longhorns

    39" tip to tip, 3 1/2" at base of horns. Mesquite, wenge and bloodwood. Go Texas!
  4. Replies
    16
    Views
    2,863

    Richard, great outcome with a redesign...

    Richard, great outcome with a redesign opportunity. Clever.
  5. Replies
    8
    Views
    2,956

    Eric, I have experienced the same thing. I...

    Eric, I have experienced the same thing. I believe it is not tear out but a vibration as you try to turn near the edge of the bowl half. The vibration causes the gouge or scraper to bounce causing...
  6. Replies
    18
    Views
    3,132

    Curious Richard, what type bottom did you use?

    Curious Richard, what type bottom did you use?
  7. Replies
    8
    Views
    1,639

    I have 2 moffet lights on my lathe that are...

    I have 2 moffet lights on my lathe that are terrific, however, the type bulb is important. I found that standard bulbs put out so much heat that they are uncomfortable. I found some 5500K twisty...
  8. Replies
    19
    Views
    2,075

    Great form Steve. I like it.

    Great form Steve. I like it.
  9. Replies
    19
    Views
    2,913

    Segmented Bowl "Longhorns"

    Bloodwood, Shadua, and Maple. 8.5" H, 7.5" W
    Alternate titles: "Go Texas" (if you are from Texas); "A Lot Bull" ( If you are from Oklahoma) Critique welcome.
  10. Replies
    20
    Views
    15,411

    Build a zero clearance fence. I use MDF (shown...

    Build a zero clearance fence. I use MDF (shown in Malcolm's book) Then take the blade all the way through the cut and let it stop before raising it. If you bring it up before the blade stops, the...
  11. Replies
    20
    Views
    15,411

    Mike, I started with a sled. It was ok, but now I...

    Mike, I started with a sled. It was ok, but now I have gone 100% to a miter saw. I consider it more accurate, safer and faster. An added plus is that you don't have to store multiple sleds.
  12. Replies
    9
    Views
    994

    Thanks for the responses. I knew I could count on...

    Thanks for the responses. I knew I could count on this forum for good advise. Actually it is my wife who wants to cut (on my bandsaw) some sheet copper for jewelry. Based on the replies, I will let...
  13. Replies
    9
    Views
    994

    Metal cutting on bandsaw?

    Is there any reason that I can't put a metal cutting blade on a standard bandsaw and cut thin metal?
  14. Replies
    58
    Views
    9,751

    It is always good to try out new ideas. We all...

    It is always good to try out new ideas. We all learn from them. In this case, I would say the results were well worth your effort. Great job.
  15. Replies
    16
    Views
    3,206

    Fantastic piece. Well done!

    Fantastic piece. Well done!
  16. Replies
    18
    Views
    4,799

    Oneway correction

    I believe the spindle thread on all Oneway's is M33-3.5
  17. Replies
    17
    Views
    2,173

    Thanks, Malcolm. That is a good point that had...

    Thanks, Malcolm. That is a good point that had not occured to me.
  18. Replies
    12
    Views
    2,662

    Nice job Richard. Shows that segmented turners...

    Nice job Richard. Shows that segmented turners are not restricted to little pieces.
  19. Replies
    20
    Views
    4,314

    I have the same dust collector and I love it. It...

    I have the same dust collector and I love it. It did blow out the bag that came with it however. I replaced it with a "contractor" plastic trash bag from home depot and haven't had a problem for 18...
  20. Replies
    17
    Views
    2,173

    Surprised at replies

    Thank you all for your comments. Frankly, I am surprised that the preference was for the muted colors. I will definitely keep that it mind in the future. Holly is available on ebay. Search for holly...
  21. Replies
    17
    Views
    2,173

    Segmented Wood comparison critque

    On 01-28-09, I posted the picture on the left. My concern was that the woods that I had used (mesquite & maple) did not have enough contrast. Although comments were kind, I still believed more...
  22. Replies
    14
    Views
    1,683

    Great job Richard!

    Great job Richard!
  23. Thread: Mobius

    by Harvey Crouch
    Replies
    23
    Views
    3,111

    Art, the staves were rough cut to 3 7/8". You...

    Art, the staves were rough cut to 3 7/8". You will lose an 1/8" or so while turning. The bowl diameters are 7 1/2".
  24. Thread: Mobius

    by Harvey Crouch
    Replies
    23
    Views
    3,111

    Thanks, Richard. It is 18" high; 13" wide. 8...

    Thanks, Richard. It is 18" high; 13" wide. 8 quarter bowls and 3 half bowls.
  25. Thread: Mobius

    by Harvey Crouch
    Replies
    23
    Views
    3,111

    Mobius

    I just finished this mobius. The wood is bloodwood and maple. Malcolm told me the number of bowl segments required but not how to assemble them. I have to admit that it took me 3 or 4 hours to figure...
Results 1 to 25 of 37
Page 1 of 2 1 2