Search:

Type: Posts; User: Chris Harry; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thanks everyone for the ideas! I completed the...

    Thanks everyone for the ideas!

    I completed the box part itself by using pocket screws to get 3 of the sides together then glued the 4th side on once the box was fastened to the pipe (I used scraps...
  2. Face frames around 4 sides, how to join them

    Im currently rebuilding the lally column covers in our remodelled basement. Of course the wife took to pinterest and found some fancy looking thing (its just a box!) which is the standard box around...
  3. Replies
    23
    Views
    5,246

    Might also serve you well to check out the 12V...

    Might also serve you well to check out the 12V offerings.

    I bought into 12V and 18V milwaukee stuff, and the 12V brushed drill is the tool thats seen the most use. 18/20V not really required to...
  4. Replies
    33
    Views
    5,751

    Mine were a little challenging because the stairs...

    Mine were a little challenging because the stairs were mounted with the stringers protruding past the finished wall by about 1" or so, and there was no skirt board (the trim looking board that goes...
  5. Replies
    33
    Views
    5,751

    Heh my Lowes store didnt seem to mind as much...

    Heh my Lowes store didnt seem to mind as much about what was inside as much as the fact that they had to price match to about 50% of their normal price! 19.99 on homedepot.com, 35.99 on lowes.com
    ...
  6. Replies
    33
    Views
    5,751

    I just went thru this same project (convert...

    I just went thru this same project (convert carpeted basement stairs to hardwood) and used this exact same tool. Except I ordered it from Lowes, ship to store , and had them match Home Depots price...
  7. Replies
    59
    Views
    10,177

    My only problem with Ridgid 12V is the lack of...

    My only problem with Ridgid 12V is the lack of more tools. The Milwaukee M12 line is huge, Bosch has more tools than Ridgid but not as many as Milwaukee (at least here in the US), etc.

    My brother...
  8. Replies
    59
    Views
    10,177

    I recently "consolidated" to one set of cordless...

    I recently "consolidated" to one set of cordless tools.

    I had a set of 18V Ridgid NiCD tools which worked fine....the battery packs were starting to go so I had them replaced under warranty with...
  9. Its a depth lock (2nd pic in the left column...

    Its a depth lock

    (2nd pic in the left column on this review page: http://www.newwoodworker.com/reviews/dw735rvu.html)
  10. Replies
    19
    Views
    4,628

    The DeWalt 734 planers are one thing that have...

    The DeWalt 734 planers are one thing that have never left HD or Lowes. My local Lowes had it down to $330 at one point, like they were going to clear them out, but then they put the price back at...
  11. Incra Ultra TS....upgrade to LS or replace?

    I have an old-ish Intra Ultra setup on my table saw. While I love the fence (and all Incra stuff Ive ever purchased), I hate having to reach far far away to adjust it. The newer version (leadscrew)...
  12. Yeah I was assuming that will happen....but I...

    Yeah I was assuming that will happen....but I wanted to be sure there was a way I could get the 90 close to begin with, otherwise Id be fighting the 45 AND the 90. Now that I know the 90 can get...
  13. You are correct, I mistyped it. Should have put...

    You are correct, I mistyped it. Should have put .0015.
  14. Thanks again everyone. Got home from work and...

    Thanks again everyone.

    Got home from work and went right to the saw (much to the chagrin of the wife :) )

    Pulled that right rear bolt out completely, just barely loosened the left side bolts...
  15. First off, thanks for all the replies. VERY...

    First off, thanks for all the replies. VERY helpful information and gives me a bunch of things to try/look at.

    Im not sure why I got a full kerf blade forever ago....I thought I read the saw...
  16. Table saw alignment, cant get it quite right

    A few weeks ago, I had a kickback incident with my Ridgid R4511 (granite top) table saw. Because of it I decided to check the alignment of everything.

    The blade is .003 out of parallel with the...
  17. Replies
    19
    Views
    4,628

    They stopped stocking them around here (and...

    They stopped stocking them around here (and presumably most if not all stores) probably 4 or 5 years ago.

    I think they finally realized having all that stock just sitting there collecting dust was...
  18. Replies
    1
    Views
    711

    Any Creekers in the Lebanon TN area?

    Looking at an Ebay item in Lebanon TN that is local pickup only.....Im not anywhere near TN :) but figured Id ask if anyone might be available to take a look and possibly ship it up to me (on my...
  19. Replies
    9
    Views
    1,442

    Thanks for the tips everyone, definitely seems...

    Thanks for the tips everyone, definitely seems easier than I thought.

    I agree thicker more durable material should be in order, but the window is installed such that the 1x4 is actually right at...
  20. Replies
    9
    Views
    1,442

    Need to "slope" flat stock

    I need to make new exterior stops for a couple of my windows. The current material is not good enough (finger jointed pine that split from sun/heat/cold), and while I was at it I wanted to make sure...
  21. Replies
    25
    Views
    3,453

    I thought about a MultiMaster last year actually....

    I thought about a MultiMaster last year actually. I have the Dremel version of it and never liked it because it always ended up burning whatever material I was trying to use it on. Once I replaced...
  22. Replies
    25
    Views
    3,453

    I was thinking the 611 would make a great xmas...

    I was thinking the 611 would make a great xmas present to myself as well :)

    I actually dont have any small routers (PC 6518 in a lift, DW618 for handheld work.....not exactly small), and I do have...
  23. I found an article on both the new PC and DeWalt...

    I found an article on both the new PC and DeWalt trim routers. It noted that the D base (DeWalt only) did not accept the bushings. it did not say that the fixed base on the PC didnt accept them,...
  24. I was thinking about pulling the trigger, I have...

    I was thinking about pulling the trigger, I have just the use for it.....mortising a door jamb thats already in place.

    But alas, the only base that can accept the bushings is the plunge base, kind...
  25. Replies
    45
    Views
    11,108

    Last communication I had with Kevan at Akeda was...

    Last communication I had with Kevan at Akeda was it (the 24" model) would be available March/April of 2011 at the earliest.

    Only thejigstore.com is a reseller in the US....someone on this forum...
Results 1 to 25 of 262
Page 1 of 11 1 2 3 4