Search:

Type: Posts; User: David J Blackburn; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    1,282

    To the original question, I would say it's...

    To the original question, I would say it's possible but unlikely.

    I'd wager you'd get 1 7/8 and 1/2" parts, but unlikely you'll get 3/4".

    I think you Resaw at 2 1/8 or even 2 1/4 to be safe....
  2. Replies
    15
    Views
    4,017

    I've had one for a couple of years now; I find...

    I've had one for a couple of years now; I find that if I am running a wide board through (more than 8-10" or so), it cannot take much of a cut at all. Very consistent with what you've said. I've...
  3. Replies
    12
    Views
    1,682

    This is his #1. He’s concerned about making the...

    This is his #1. He’s concerned about making the box joint cuts on the narrow part after doing it, because his board isn’t flat. At least, if I’m reading his concern right. The video he links to in #1...
  4. Replies
    12
    Views
    1,682

    I’d go with #1. If you are worried about the...

    I’d go with #1. If you are worried about the strength of the glue up when cutting the box joints, use a backer board tightly clamped to the front to give it more support and should keep you from...
  5. Replies
    62
    Views
    9,301

    Yes, this. I said the same thing the other day,...

    Yes, this. I said the same thing the other day, but I wouldn't fiddle with the settings based on what's in those pictures. You're likely to make things work. You have a board with a lot of cupping...
  6. Replies
    62
    Views
    9,301

    Late to the game maybe, but based on those...

    Late to the game maybe, but based on those pictures, nothing seems to be wrong. In the 4th picture, the board is resting flat on the jointer bed through the first 1/3 or so, then raised, then...
  7. Replies
    8
    Views
    1,069

    Happened to me. No idea why - it didn’t snap...

    Happened to me. No idea why - it didn’t snap completely, so I trimmed it down and put it back on (so I could finish what I was doing) and it has worked fine since. I did order a replacement on...
  8. Replies
    6
    Views
    1,387

    So - follow up - That paint is the thickest...

    So - follow up -

    That paint is the thickest paint I’ve ever seen, and I’m having a lot of trouble applying properly. Any hints? I’m using a nylon brush and it looks awful.

    I am not a pro at...
  9. Replies
    6
    Views
    1,387

    Awesome, thanks for the advice.

    Awesome, thanks for the advice.
  10. Replies
    6
    Views
    1,387

    Finishing Bathroom Vanity

    Hey all -

    Looking for some finishing/paint/sealer advice. I’m replacing the vanity in a half bath (powder room?) and have built a new vanity as a simple MDF carcass with a popular face frame and...
  11. Don - I PM’d you. I’m in Bethesda. Not a big...

    Don - I PM’d you. I’m in Bethesda. Not a big window due to work travel, but if you can swing by tomorrow during the day, I can help.
  12. Hey - what did you use for the clamp racks? Are...

    Hey - what did you use for the clamp racks? Are those just 12” hooks or something?
  13. It is, as a matter of fact. The Feb 18 issue is...

    It is, as a matter of fact. The Feb 18 issue is out already.
  14. Just to be clear, the MJ splitter is *NOT* a...

    Just to be clear, the MJ splitter is *NOT* a riving knife. It's a splitter. You can't use it on non-through cuts (unless it's a very deep non-through cuts) and you can't use it on non-90 degree...
  15. Replies
    6
    Views
    2,312

    Axminster tool makes a jig that does the the same...

    Axminster tool makes a jig that does the the same thing and is a bit cheaper. I ordered it direct from them in the UK, but I think they now sell it at Lee Valley too. Cheaper than the woodpecker...
  16. Replies
    44
    Views
    10,570

    A 3hp machine should be good at 20 amps, and a...

    A 3hp machine should be good at 20 amps, and a 5hp machine should be good with 30 amps, so you should be fine to run a 3hp DC at the same time as any of the other tools. Unless you outfitted your 66...
  17. Replies
    30
    Views
    12,242

    Youve got 220 coming from the pole, for sure....

    Youve got 220 coming from the pole, for sure. With the proper wire and breaker size, you'll get 5hp. Without the right breaker size, you'll pop the breaker and without the right wire size, you risk...
  18. Replies
    18
    Views
    4,250

    Holben gives free shipping and 10% off the...

    Holben gives free shipping and 10% off the standard Byrd prices. They don't take the SMC membership discount on the Shelix heads. But it's still a good deal.
  19. Replies
    80
    Views
    14,414

    Poll: Domino (bought used at like 70%) Ets 125 Forex...

    Domino (bought used at like 70%)
    Ets 125
    Forex 90
    TS55 with two rails
    Ct26

    I keep thinking about a jigsaw, but I can't justify it, because the cordless Bosch I have works well enough. Would...
  20. Yes. I live in DC and feel like driving down...

    Yes. I live in DC and feel like driving down there to get it would be a reasonable thing to do. Go grab it
  21. Replies
    10
    Views
    1,474

    I had the exactly same. Added the Woodpecker lift...

    I had the exactly same. Added the Woodpecker lift and PC7518 motor, add use my Bosch (1617/18) in hand now. Huge improvement with the lift.
  22. Replies
    5
    Views
    957

    I've had that for a while. It works. I also just...

    I've had that for a while. It works. I also just bought a lift because "It will work. You won't like it, but it will work." Is the truest thing ever said.
  23. Replies
    11
    Views
    4,280

    A jointer isn't complicated. If you can get the...

    A jointer isn't complicated. If you can get the tables coplanar, then its a great deal. If you cant, then it's not.
  24. A question, as I think about getting a similar...

    A question, as I think about getting a similar unit. What did the external hepa filter kit cost?
  25. Being a litigation attorney is more lucrative...

    Being a litigation attorney is more lucrative than most jobs, yes.

    There are no damages available as a remedy in the ITC. If SS wins in a patent suit in district court - which would likely also...
Results 1 to 25 of 42
Page 1 of 2 1 2