That last one generally requires a mill. You would need to find a drill press with v-ways for the table or head adjustment.
Type: Posts; User: Don Sundberg; Keyword(s):
That last one generally requires a mill. You would need to find a drill press with v-ways for the table or head adjustment.
Is the twist lock outlet behind your saw in the pictures a 240 volt or 120 volt outlet? I would check the wiring to see what is running to it for wire size and use it regardless of voltage. Making...
Just another though for the guys cutting down your fence rails. You can have a competent welder move the fence to the right side of the T-square making an L square. It would increase your rip on...
You could probably run the 10 hp phase converter with a 30 amp breaker but not with the loads you are looking at running. I ran my 10 hp phase converter off of a 30 amp circuit until this weekend. ...
Well at least we published a nice guide for choosing a drill press.
Whatever you get, consider the stroke. I have a little benchtop drill press with a 2.75" stroke and I am always having to adjust the table. It's not hard but if you have a fixture clamped to the...
https://www.gitsmfg.com/catalog/
Only thing I can come up with is to rent a tank of CO2 and a regulator and use a CO2 detector to check your joints. You could use freon and have your favorite AC guy check it out but CO2 should be...
https://www.northerntool.com/shop/tools/category_tarps-canopies-shelters+instant-garages-instant-shelters
Or the vendor of your choice. I was told in an earlier career that they were very...
I would clamp the two slides together so they lined up and plug weld them together with TIG. If you use bolts, be sure to lock tite them the last time you assemble them. If you can find a Z-bracket...
Northern tool does that with some of their catalogs. There are a few extra numbers in the catalog part number that gives them the catalog or mailing that you are ordering from, even if you are...
I hauled a huge linden and a pretty good sized hackberry off with my brother. None of if was sawn but they were both big enough. Had a hose start leaking on the skid loader so we had some down time....
The last irregular shelves I did I took strips of wood about 3/4" x 1/8" and hot glued them together around the perimeter in place on the shelf pins. I then used these to mark the shelf boards and...
Your motor nameplate has 2 wiring diagrams on it (low voltage and high voltage) Wire the motor as shown on the plate for 120V. You don't need to change anything at the pressure switch. You then need...
They mentioned this site for DF500 knock down hardware. Doesn't really have a draw down system like the Festool offers.
http://www.dominofix.com/
New Domino Knock Down Connectors
I don't even have a Domino but they look cool. Showed up in my Facebook feed.
http://festoolusa.com/power-tools/connectors/
B4269 just under $1k at our friends at holbren. Still a little rich for me. There may be a kit from Grizzly.
It wouldn't work for molding any more.
Rolair has this one but its seems to got for 1299.
https://www.rolair.com/products/air-compressors/wheeled-electric/3095k18
3 hp 2 stage dual hotdog portable tank.
If you need to move the...
You need to strech your budget or wait for a sale on a Quincy QT-54 or similar. It's a 5 hp 60 gal vertical tank two stage pump thats good for 15.4 cfm @ 100 psi. If the vertical it too tall they...
We are looking at a new TS for work and my recommendation was a SawStop if only because the insurance co will demand it soon enough. We have an old Craftsman contractor saw that needs a full rebuild...
No wood work this weekend (my wife would very much prefer that I get back to work on trim). Found leaf spot on the cherry trees Sat night and got them sprayed Sun. Got the new strawberry plants in...
That's been the biggest part of my woodworking so far is making trim for my house. A couple of words of advice: When running tall baseboards it is much easier to make if you add extensions to your...
I watched This Old House for the first time in a long time and one of the segments was in a custom cabinet shop and they had this electronic stop.
http://razorgage.com/
I thought it was...
The only thing that tends to blow up in a compressed air system is PVC piping. I do personally know someone who had it happen. I would avoid it if at all possible.
Now if your pressure switch...
What kind of projects do you want to make? If you are looking at making furniture type pieces with dovetails, and mortises, then hand tools and some practice is the way to go. You will never regret...