Search:

Type: Posts; User: Mike Gottlieb; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    845

    Yes, I do plan to do both. I realize that the ID...

    Yes, I do plan to do both. I realize that the ID has to be larger that 1/4". 5/16" will give me a 1/32" clearance - as long as there is not too much deflection, it should work. As for the OD, I want...
  2. Replies
    6
    Views
    845

    Which Guide Bushing?

    I am planning to use a 1/16" router bit for inlay work. Since I will be making a template to follow, which size bushing would you recommend? The bit will have a 1/4" shank. I am thinking
    maybe a...
  3. Replies
    14
    Views
    1,576

    Bandsaw Blades

    Need recommendations for 1/4" blades to be used on 20" bandsaw. I have used regular carbon steel blades in the past, but they have a short life and tend to break easy.
    Many thanks, Mike
  4. Fishtail Chisels for Half Blind Dovetails

    I noticed that Blu Spruce tools is offering their fishtail chisels on sale. Has anyone used these chisels for half blind dovetail work? Please give me your opinions.
  5. Replies
    0
    Views
    351

    Infeed table on older Hammer A3-31

    Has anyone had experience removing the infeed table from an older Hammer A3=31 jointer/planer? I have to remove the table to do some work on the feeder block. I need some advice regarding the hinge...
  6. To Erik Loza: Can you help with the questions on...

    To Erik Loza: Can you help with the questions on this subject?
  7. Conversion of Hammer A3-31 to Shellix Head

    I am currently in the process of converting my 1st generation Hammer A3-31 to a Shellix cutterhead. I am at the point where I need to remove the infeed table in order to remove the old cutterhead...
  8. Replies
    2
    Views
    614

    This slab was mostly red in color with two thin...

    This slab was mostly red in color with two thin black stripes running across it.
  9. Replies
    2
    Views
    614

    Black Coolibah Lumber

    I was at a wood dealer today and saw a slab (approx. 5' x 21" x 1" thick) labled as "Black Coolibah." I am only familiar with Red Coolibah burl from Australia. I have never seen Coolibah sawed in...
  10. Replies
    24
    Views
    4,129

    I run mine on a 20 amp line and have never had a...

    I run mine on a 20 amp line and have never had a problem.
  11. Replies
    18
    Views
    2,774

    LN Sharpening Jig

    For those of you that own this jig, I need some help. I have two sets of chisels,Veritas PM11 and Stanley 750's. All of my plane blades are Veritas. Can I use this jig for sharpening these items? I...
  12. Replies
    9
    Views
    1,217

    Thanks all. I think a 2mm gap is what I will use....

    Thanks all. I think a 2mm gap is what I will use.
    Regards, Mike
  13. Replies
    9
    Views
    1,217

    Shiplap Back

    I am about to install a maple shiplap back on a chest of drawers. I need some advice on the width of the expansion gap between the four maple boards approximately 36 x 5. Appreciate any help.
  14. Replies
    3
    Views
    668

    cut nails for nail gun

    Is there such a thing as nails for a nail gun that simulate cut nails?
  15. Replies
    2
    Views
    652

    Contrasting Wood Splines

    I am building two small boxes with maple tops and jacobs boxes. I need to make visible splines. Should I go with jatoba or some other wood for the slides?
  16. Replies
    22
    Views
    3,721

    I agree with Tom. I just started spraying and had...

    I agree with Tom. I just started spraying and had a devil of a time getting vertical surfaces right - sags and runs. The folks on this forum gave lots of good advice. Like most have said, it takes...
  17. Replies
    21
    Views
    7,627

    Tom, Specifically, which floor finishes have you...

    Tom, Specifically, which floor finishes have you used that are that tough?
    Mike
  18. High John, Just tried speeding up my technique. I...

    High John, Just tried speeding up my technique. I got no runs or drips. The finish did have a light pimply feel to it. Maybe I should open the fluid delivery more? Will sand and try another coat...
  19. Thanks John. I will try speeding up.

    Thanks John. I will try speeding up.
  20. Problem spraying enduro-var on vertical surface

    I am trying to finish a chest with enduro-var. The top and trim sprayed beautifully. When I try to spray the vertical sides I get huge runs. I tried turning the fluid down to one turn from 1 and 3/4...
  21. Replies
    8
    Views
    2,664

    Neil's blotch control is a water-based product. I...

    Neil's blotch control is a water-based product. I checked with Charles Neil before application. He confirmed that it is fine to use under Enduro-Var and other water-based products i.e. High...
  22. Replies
    8
    Views
    2,664

    I should have added that I have already put on...

    I should have added that I have already put on the recommended two coats of Charles Neil Blotch Control, so the grain has already been raised and knocked down.
  23. Replies
    8
    Views
    2,664

    Sanding between coats of Enduro Var

    I am about to spray a cherry chest with Enduro Var. This will be my first time with this finish. What do you recommend for sanding between coats?
  24. Replies
    6
    Views
    2,763

    I would suggest Arm-R-Seal wipe on finish by...

    I would suggest Arm-R-Seal wipe on finish by General Finishes. Easy to use and provides a very durable finish.
  25. Replies
    2
    Views
    1,030

    GF Endo-Var

    I am about to use and spray Endo-Var for the first time on a cherry chest of drawers. The chest is prefinished with Charle Neil's blotch control. I want to end up with a satin finish. Should I apply...
Results 1 to 25 of 113
Page 1 of 5 1 2 3 4