Clint, how does the laminate hold up to the heavy rolling machines? I am considering this, but worried about my TS, jointer and such causing dents when I roll them around.
Type: Posts; User: John Baranowski; Keyword(s):
Clint, how does the laminate hold up to the heavy rolling machines? I am considering this, but worried about my TS, jointer and such causing dents when I roll them around.
I have a boombox that is over 20 years old that has been in the shop for 10 years and no issues. it is plenty loud enough to be heard even over machines. I don't even think about it other than to...
Thanks for all the input everyone. I appreciate it. I put the known data into excel, and the curves for the two machines are identical for the portions that Oneida posts data. The SDG does not...
At the very least, put a reflective barrier around it. The stuff is cheap, and will keep the sun from heating it too much.
this is the same reason I go to the BORG as well. No prices or labels drives me nuts.
I am a homeowner, not a contractor. Knowing every grade of construction lumber is more than I care to...
I am looking at the 5hp dust gorilla and the Pro 2000, but can't figure out what the difference is, other than filter sensor and diy duct design. Oh, and different paint. Are those the only...
which is what I was getting at. I figured the HF one was wrong.
Seeing as how the vanes are reversed on those two impellers, which direction does the motor turn? are the HF and Rikon motors reversed from one another?
Not to rain on the parade, but other than aesthetics, what is the purpose of a pergola? To me, it seems to be a shade structure that doesn't provide shade. Am I missing something?
I am looking at another kitchen project here in the next few weeks, and am scoping out drawer slides. I would like to keep them made in the USA if possible, but I can't tell which are made here, and...
If that is what she is looking for, why buy wood furniture? Or just use poplar and paint the thing. (not a critique of you, just people who want wood that doesn't look like wood)
Now I don't quite understand this. Is this only for non-supporting walls? If you float every wall, what holds up the structure? And I would think that if the soil is prepared properly, a slab...
The $85 Bosch is actually the PS-20, which is a drill, not an impact driver. I have that one and the PS-40, the impact driver. I like it alot, and use it all the time. It is lightweight, and small...
Here you go. Problem solved.
http://www.harborfreight.com/movers-dolly-93888.html
Just an FYI, the more splits, the more degradation in signal. for normal 480i, it won't be a problem. For digital TV, especially HD, it may cause some issues. Just something to be aware of.
As was I. We had granite installed by a pro last year for $42/sq ft. The higher priced granites were still in the $60-75 range, with some outliers around $100. to stay that granite starts at $100...
If these are the prices in your area, you are getting ripped off. Granite around here starts at ~$40/sq ft, and goes up from there. You can get your own laminate at the BORG for somewhere around...
Since the light bulbs are fixed resistances, it is regulating current in effect. When you wire in parallel, you are providing a shunt which will hog all the current, burning out the dimmer switch.
Similar to what John C. stated, I have wet sanded using wet/dry paper and liberon finishing oil. It darkens the wood as oil normally would, but the pores are filled with the slurry created by the...
Check the nameplate of the motor, and find the manual if you can. The motor may be rated for 230V already.
In addition, this manual shows the settings for changing the output voltage.
...
I would use something like a car door contact, so that when it is fully open, they conduct from one side to the other. Put it on a switch, so that it is safe when closed....
Or just break of the bulb, then use a potato to get it out
To my knowledge, a VAT requires that something change the product, i.e.,
steel + Grizzly(value added) = Jointer.
Sales tax is strictly upon the sale of an item, regardless of an change in the...
Speaking of which, I wonder what Lee Valley has for us in a few days...
congrats on the twins! On a similar note, my grandfather(mother's father), mother, and sister were all born on July 21st. 3 generations on the same day. We called it Christmas II around our house.