Search:

Type: Posts; User: Brent VanFossen; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Woodcraft offers a replacement blade for the #62...

    Woodcraft offers a replacement blade for the #62 plane in their WoodRiver line, but I don't know if it's interchangeable with the Stanley 62 or only their own brand plane.
  2. Replies
    33
    Views
    3,894

    Lee Valley is using torrefied maple on some of...

    Lee Valley is using torrefied maple on some of their plane and handsaw totes. It's beautiful.

    I've also seen it in maple and poplar at one of the better lumber sellers in Portland, OR.
  3. Replies
    13
    Views
    2,080

    Very nicely done, Ron. It's beautiful. I've never...

    Very nicely done, Ron. It's beautiful. I've never done kumiko.
  4. Replies
    67
    Views
    13,316

    Malcolm, it could be that I heard or remember...

    Malcolm, it could be that I heard or remember incorrectly, but it's not a typo.
  5. Replies
    67
    Views
    13,316

    I spoke with Dave Jeske at the Portland...

    I spoke with Dave Jeske at the Portland Lie-Nielsen event this weekend. He had the new saw there, and it is as classy and beautiful as you would expect from Blue Spruce. The saw can be set to allow...
  6. Replies
    9
    Views
    5,572

    Jack, I have no firsthand knowledge of this....

    Jack, I have no firsthand knowledge of this. However, doing a quick google search of "83-651 delta motor capacitor" turns up others who have had similar problems. Perhaps these threads will be useful...
  7. Replies
    36
    Views
    5,080

    You could always install a square column in the...

    You could always install a square column in the room so you could push the table up against it...

    Joking aside, I would trim the long board flush. I like the coaster or bowl idea.
  8. Replies
    10
    Views
    2,831

    I can't answer for the others, but I use the...

    I can't answer for the others, but I use the Benchcrafted hardware for mine with the Crisscross support. This is rigged specifically with a degree or two of toe-in to make sure the vise chop contacts...
  9. Replies
    3
    Views
    1,326

    Nice write-up, Jim. Taking a new road can be a...

    Nice write-up, Jim. Taking a new road can be a lot like being on vacation, if you let it. And good finds in your antique shopping.
  10. Thanks for posting the troubleshooting...

    Thanks for posting the troubleshooting instructions. I hope that I never need them, but I will save them for later.
    Maybe you said and I missed it, but you know how to bypass the safety feature,...
  11. I'm really sorry to hear of your experiences with...

    I'm really sorry to hear of your experiences with the Bosch Reaxx. It sure is disappointing when a purchase doesn't work out. I don't have any other information to share about the saw to help you,...
  12. Replies
    4
    Views
    1,881

    I, also, have done cutting operations after an...

    I, also, have done cutting operations after an hour or so of clamp time with no problems. But I would not do anything that puts a new joint in any significant bending or tension for about 24 hours.
  13. Replies
    30
    Views
    21,505

    I've enjoyed this thread, and it looks like your...

    I've enjoyed this thread, and it looks like your sled worked well. As for the card scraper, that work will tire the thumbs and fingers!
  14. Replies
    17
    Views
    2,638

    I don't have first-hand experience with wenge,...

    I don't have first-hand experience with wenge, but padauk becomes very much darker. I have a piece of padauk that was the orange color of yams when freshly cut, but is now a luscious chocolate with...
  15. Replies
    10
    Views
    2,332

    Those are pretty nice. Good looking bench, too.

    Those are pretty nice. Good looking bench, too.
  16. Replies
    338
    Views
    99,582

    I keep a wand-type metal detector in my shop....

    I keep a wand-type metal detector in my shop. Every piece of suspect wood undergoes a full sweep on each surface before I apply a hand plane or run it across or through any of my machines. There's no...
  17. I had the same issue with the stretcher in my...

    I had the same issue with the stretcher in my build, and I chose to trim some material out of the stretcher to allow the nut to be removed should the need arise. This was not a mistake on my part,...
  18. Replies
    20
    Views
    4,704

    Looks like a fun project. Thanks for the writeup...

    Looks like a fun project. Thanks for the writeup and all the photos.
  19. Beautiful work. And congrats on your first...

    Beautiful work. And congrats on your first dovetails!
  20. Thanks for that, Cliff. I was shooting for 2",...

    Thanks for that, Cliff. I was shooting for 2", but on my first glue-up, I ended up with some bow in my filler, and I had to cut it apart and glue it again. I'm at 1 7/8 for the filler now, and the...
  21. Roubo Split Top Gap Dimensions and Wood Movement

    I'm at the point in my split top Roubo bench build per the Benchcrafted plans that I need to cut and fit the short rails of the base. These are the cross pieces that will support the two halves of...
  22. Replies
    11
    Views
    2,333

    Thanks for all the responses. The cracks don't...

    Thanks for all the responses. The cracks don't seem to affect the soundness of the boards, despite some of them being in the joinery area; for my hidden spline joints, I don't think they will affect...
  23. Replies
    11
    Views
    2,333

    Repairing small walnut cracks

    I found and bought a highly figured walnut board that I plan to use for making a tea box for my wife for Christmas (shhh!). When I resawed it to thickness, I found several cracks on the previously...
  24. Replies
    22
    Views
    4,358

    Everything worked fine for me. I found a few...

    Everything worked fine for me. I found a few planes that I needed and have a nice package coming sometime in the next week or so.

    What can I say? This is the only sale of the year that I pay...
  25. Replies
    11
    Views
    5,463

    Thanks, guys. I really appreciate the feedback....

    Thanks, guys. I really appreciate the feedback. Jim, the idea of being able to use the top as a giant clamp has me excited and thinking - that's something I had not considered. Joe, Jim, James,...
Results 1 to 25 of 211
Page 1 of 9 1 2 3 4