Search:

Type: Posts; User: Mark Sipes; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Have you tried to raise the cutter at the screw...

    Have you tried to raise the cutter at the screw fitting (). Sounds like the down travel is set high.

    .
  2. Can you post a photo of your machine. .

    Can you post a photo of your machine.



    .
  3. Replies
    29
    Views
    15,854

    Dylan....... Been over a year since a post. ...

    Dylan....... Been over a year since a post. Hope you have mastered the HP350 by now. Did you get the spindle and belt tension rods fixed. Leveling of Dyna Grip table or nose vacuum. and of...
  4. Replies
    12
    Views
    4,630

    Go to MeterMall.com and purchase "smoke...

    Go to MeterMall.com and purchase "smoke generators" Regin Smoke Emitters $13.95 -- Dense white smoke for airflow and leak tests. Range of burn times and volumes..

    Purchase smoke generator...
  5. My Firmware is 1.22......... I recall only...

    My Firmware is 1.22......... I recall only updating it once and really saw no change to the machines performance. I believe the install was per remote.....


    .
  6. What is your SP # Mine is 0925 Did...

    What is your SP # Mine is 0925

    Did you load the Trotec Print Driver....... Is it visible in the Printer & Faxes Directory.


    Running 6.3.1 XP Pro Corel X6

    Operating Hours ...
  7. Replies
    6
    Views
    2,882

    What is the intended use. JDS sells impact...

    What is the intended use.

    JDS sells impact modified acrylic sheet 1/32, 1/16, 1/8 in 50 colors....

    ...
  8. So I looked at my version of JLS (NH Job Layout...

    So I looked at my version of JLS (NH Job Layout Software) and it lists the 400D Cyl, M300DAT, M305DAT, M400DAT, 405, 600, 605......

    as supported machines.

    I find JLS easier to use than...
  9. When you installed the JC software did you load...

    When you installed the JC software did you load the TROTEC Engraver Printer Driver It will show up in the printer files as a local port.


    .
  10. How is your effort to get the 8003 up and running...

    How is your effort to get the 8003 up and running again?

    I have a Speedy 100 I purchased in 2000. The only port I have to the machine is the old 25 pin Serial port I am able to run Win XP with...
  11. Replies
    3
    Views
    4,725

    There should be a P/N for the current board you...

    There should be a P/N for the current board you have installed. The CPU itself seems to be available on several on-line sites.

    What is the make / model of your computer??




    .
  12. Replies
    21
    Views
    5,180

    The I guess you are not a registered...

    The I guess you are not a registered business....... Part of your license is a Resales Certificate that provides for purchasing wholesale. But you still need to collect and pay the collected sales...
  13. Replies
    29
    Views
    15,854

    I assume you do not want to use a nose on your...

    I assume you do not want to use a nose on your rotary spindle...


    I use a dial indicator to level my table by placing strips of tape on the channel that holds the table plate in place

    The...
  14. Replies
    21
    Views
    5,180

    try .monroeid.com Any business that sells...

    try .monroeid.com


    Any business that sells goods or taxable services within the state of Iowa to customers located in Iowa is required to collect sales tax from that buyer. This will include all...
  15. Replies
    21
    Views
    5,180

    monroeid.com .

    monroeid.com



    .
  16. I'm a novice.... can you give a better...

    I'm a novice.... can you give a better description as to what is happening. When you move the laser head to say 4" x / 4" y
    you don't see the + in JC...... and you said the Red dot is visible on...
  17. Replies
    7
    Views
    4,766

    I have a C25 and the system runs on XP not sure...

    I have a C25 and the system runs on XP not sure you can get it to run on Win7. I can send send a driver up dat to you but again for XP.

    ....send email address to my personal
  18. Replies
    4
    Views
    4,134

    That style unit comes with several output levels ...

    That style unit comes with several output levels Check Amazon.

    "air compressor for laser cutter" Amazon.com : VIVOHOME Electromagnetic Commercial Air Pump 1110GPH 50W 8 Outlets 110V for Fish...
  19. Was there a solution to your problem.?? .

    Was there a solution to your problem.??


    .
  20. Replies
    4
    Views
    4,134

    What size laser do you have (wattage) , What was...

    What size laser do you have (wattage) , What was the LPM/GPM of the air compressor that came with unit

    Here is a reasonable unit ...
  21. Replies
    8
    Views
    6,706

    I have rarely had a need to laser to the upper...

    I have rarely had a need to laser to the upper edge of a plate, but since I can see on the monitor the image to be lazed I can place a magnet at a location not to be engrave for hold down pressure. A...
  22. Replies
    16
    Views
    4,843

    Glen I appreciate the new tip you just taught us...

    Glen I appreciate the new tip you just taught us all, Bert may not have understood the process but you saved me several steps I have been having to go through to get to the final step..

    I have...
  23. Replies
    8
    Views
    6,706

    That's where I installed the 12" x 24" steel...

    That's where I installed the 12" x 24" steel sheet..


    .
  24. Thread: Software

    by Mark Sipes
    Replies
    2
    Views
    1,975

    I use Quickbooks Pro... Ordering, Invoicing,...

    I use Quickbooks Pro... Ordering, Invoicing, Payroll, Estimates, Statements, Banking, Inventory, Taxes..... use all or part

    .
  25. Replies
    8
    Views
    6,706

    I have a TROTEC also... From day one I double...

    I have a TROTEC also... From day one I double side taped a sheet of Trophy brass steel sheet ($6-8) (12"x 24") to the bed and with 10 name tag magnets nothing moves . I laser 15 x 5 USCG Doc plates...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4