Search:

Type: Posts; User: Paul A. Clark; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: Marker??

    by Paul A. Clark
    Replies
    14
    Views
    2,419

    Hey Lowell, for mesquite I have had good results...

    Hey Lowell, for mesquite I have had good results with a silver artist pencil. Easier to see line after the fact
  2. Replies
    12
    Views
    4,214

    Alex, i have found on deep voids, is to do...

    Alex,

    i have found on deep voids, is to do multiple small pours. Hit each pour with the torch, let it cure overnight and rinse, repeat until void is filled. This does take an additional day or two...
  3. Replies
    8
    Views
    2,595

    John, Fantastic execution love the design and...

    John,

    Fantastic execution love the design and highlighting the live edge.
  4. Replies
    14
    Views
    4,117

    I have used the Kaizen, Festool and Craftsman...

    I have used the Kaizen, Festool and Craftsman foam. All work as advertised, by the craftsman is much more difficult to layer. I just completed 6 drawers on my under bench cabinet. Could be be happier...
  5. Would not have put a pull at all. Let the work...

    Would not have put a pull at all. Let the work show thru. Like Art mentioned could you Add something instead of the knob?
    other than that the box looks great, nice work.
  6. Replies
    4
    Views
    1,494

    Alex, check mesquiteburl dot com. Good guys, good...

    Alex, check mesquiteburl dot com. Good guys, good product, on site kiln. I have used them several occasions and always been happy. Just get ready for the bill.
  7. Replies
    7
    Views
    1,598

    Steve, I just got some router bits back from...

    Steve, I just got some router bits back from Woodcraft here in Austin. All TX Woodcrafts use Cooks in San Marcos. Done here its a week turn around. My bits came back better then new and not expensive.
  8. Replies
    9
    Views
    3,799

    You might check with Mesquite Burl dot com. Good...

    You might check with Mesquite Burl dot com. Good guys, but you have probably figured out it ain't cheap
  9. Replies
    45
    Views
    7,267

    Yea, tried the ct36 with the 150/3 for the first...

    Yea, tried the ct36 with the 150/3 for the first time on Friday. At first I thought the sander was not working,, no dust in the air no dust on the surface, no dust on me, no dust anywhere. That might...
  10. Replies
    45
    Views
    7,267

    I think the more you add the steeper the slope...

    I think the more you add the steeper the slope gets. 1st go around Ct36 and TS55. "That will be enough to break down sheet good." The next day ETS150/3, Domino w/ ALL the bits and systainer and extra...
  11. Replies
    45
    Views
    7,267

    Festool Slope

    Well, thought I would not ever own any of the Green German candy. So much for that thought. I recently left the restaurant business after 30 yrs to go into the remodel business. Thought now would be...
  12. Replies
    352
    Views
    51,379

    Please count me in

    Please count me in
  13. Replies
    15
    Views
    4,773

    I have spoken to the guy that runs it. Can't...

    I have spoken to the guy that runs it. Can't remember his name now. But, seemed very easy going and knowledgeable. Have spoken to him last two years at LN hand tool event here in Austin. Would like...
  14. Replies
    27
    Views
    6,319

    Checked last week, Fine had hard maple @ $4.96...

    Checked last week, Fine had hard maple @ $4.96 BF. About to start bench build
  15. Replies
    27
    Views
    6,319

    We are about a $1 more BF here in Austin TX.

    We are about a $1 more BF here in Austin TX.
  16. Replies
    55
    Views
    13,988

    Is that the 2nd leg riding against the drum?

    Is that the 2nd leg riding against the drum?
  17. Replies
    11
    Views
    1,838

    It has arrived. Shipper was a day and a half...

    It has arrived. Shipper was a day and a half late, but got the same time off work so not a bad thing. It's set-up, but I can not use it yet. No time to add 2nd elec. panel in shop yet. You had to...
  18. Replies
    11
    Views
    1,838

    Matt Mac, Do you have a recommendation on the...

    Matt Mac,

    Do you have a recommendation on the phenolic blocks? Looked at Rockler, WoodCraft only ones I'a m seeing are for 14" saw.

    Jeff you are correct she is the LOML and is treated everyday...
  19. Replies
    11
    Views
    1,838

    Happy early Christmas to me!!!

    SWMBO jsut ordered me the Grizzly G0513P for Christmas. Shipper says it's to arrive Monday, thats pretty fast. I have to run new power to the shop to be able to use the bandsa(220v). Should be a fun...
  20. Replies
    10
    Views
    2,547

    I'll be there Saturday at 10 am

    I'll be there Saturday at 10 am
  21. Replies
    2
    Views
    1,422

    Thanks Jim Hope you and your family has a...

    Thanks Jim

    Hope you and your family has a wonderful holiday.

    Paul
  22. Replies
    2
    Views
    1,422

    Some christmas gifts

    Here are my first making boxes. One is for my FIL (maple & walnut) the other is for my BIL (maple & mesquite). The maple got a little shellac tinted with a medium brown. The tops and bottoms got some...
  23. Replies
    24
    Views
    6,774

    Jeff, almost too nice to use. Have you got your...

    Jeff, almost too nice to use. Have you got your first scratch or ding yet?
    I too like your tool tray, very innovative. I usually have my tools taking up the real estate and the project at hand...
  24. Replies
    7
    Views
    1,757

    Thanks, Tri. John your right, it does look...

    Thanks, Tri.

    John your right, it does look like a finger joint. I was watching a Cosman video, and said "I think I will give that a try."

    My wish list includes a LN DT saw or a Cosman. I have...
  25. Replies
    7
    Views
    1,757

    First attempt at Dovetails

    Here is my first try at dovetails.
    Japanese pullsaw and a sliding bevel
Results 1 to 25 of 43
Page 1 of 2 1 2