Search:

Type: Posts; User: Jeff Myroup; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    1,797

    You can get the graphite paper at Michaels or...

    You can get the graphite paper at Michaels or Hobby Lobby. I am sure you can order it from Amazon. You can make your own by using the side of a pencil and covering the back of your pattern.

    If...
  2. Replies
    10
    Views
    1,797

    I use wax free graphite paper instead of carbon...

    I use wax free graphite paper instead of carbon paper. Wax free graphite can be erased. Xylene works well for simple line drawing, but not so much for a complex pattern. If you are burning, I would...
  3. Replies
    5
    Views
    1,266

    Beall system should work

    Beall system should work
  4. Replies
    6
    Views
    1,625

    Glad you got it figured out.

    Glad you got it figured out.
  5. Replies
    6
    Views
    1,625

    Here is a diagram that should work. 239584

    Here is a diagram that should work.


    239584
  6. Replies
    6
    Views
    1,625

    The 'V' cuts do indeed indicate flow. From the...

    The 'V' cuts do indeed indicate flow. From the picture, the orange plug would be the end connected to the lathe chuck. Jumper the opposite port to the second cylinder (on back side of picture), last...
  7. Replies
    20
    Views
    2,006

    I had run out on a SN2, and thought it was the...

    I had run out on a SN2, and thought it was the chuck. It turned out to be the lathe bed was not completely level. I leveled my jet mini and never had a problem after. I did not notice anything wrong...
  8. Replies
    7
    Views
    1,364

    Very nice Tim. I look forward to meeting up with...

    Very nice Tim. I look forward to meeting up with you sometime in the near future
  9. Thread: New to SMC

    by Jeff Myroup
    Replies
    13
    Views
    2,223

    Poll: You already know my comments, so I won't repeat...

    You already know my comments, so I won't repeat them here. I think you need to ask yourself the same question a gallery owner will ask himself; "can I sell this". I think if you do what you were...
  10. Replies
    1
    Views
    1,024

    They are still very active. I don't know about...

    They are still very active. I don't know about activating an old account though.
  11. Replies
    9
    Views
    1,484

    Clinging to the "American Beauty"!!! I do plan on...

    Clinging to the "American Beauty"!!! I do plan on spending some time in the Robust booth. Maybe I can take her for a test drive :D
  12. Replies
    9
    Views
    1,484

    I will be there. Just look for the 6' 5", 275 lbs...

    I will be there. Just look for the 6' 5", 275 lbs guy acting like a kid on christmas. ;)
  13. Replies
    15
    Views
    23,507

    Paul, you can order Nichrome wire on amazon. I...

    Paul, you can order Nichrome wire on amazon. I bought a couple of rolls about 6 months ago and they were around $17.00 per roll. The rolls are not large, but will last a very long time. I would...
  14. Replies
    15
    Views
    23,507

    I would not us my pens with this. It has almost 4...

    I would not us my pens with this. It has almost 4 times the power of the burnmaster. You would most likely burn them out. They have an internal resistance of 2 or 3 ohms depending on the brand of...
  15. I think Alan summed it up very well.

    I think Alan summed it up very well.
  16. Replies
    18
    Views
    2,672

    We will have to go find a new source.

    We will have to go find a new source.
  17. Replies
    14
    Views
    1,667

    Thanks Everyone. I am really enjoying doing...

    Thanks Everyone. I am really enjoying doing these.

    Bernie, give it a shot. Leave the tenon on and turn it off if you don't like it. I have done that more than I care to admit. :rolleyes:
  18. Replies
    19
    Views
    2,445

    If you are bored sitting there with no power, I...

    If you are bored sitting there with no power, I got some bowls that need to be polished.
  19. Replies
    13
    Views
    3,257

    fantastic work!!!! I like the lucite the best....

    fantastic work!!!! I like the lucite the best. Truly exceptional work.
  20. Replies
    14
    Views
    1,667

    Thanks Tim, I am really happy with the shadows. I...

    Thanks Tim, I am really happy with the shadows. I finally got them right :D They are also super smooth and you can see the wood grain through them. This piece of wood was fantastic to burn. All the...
  21. Replies
    14
    Views
    1,667

    "Falling Leaf" Maple bowl

    I just finished the burn on the leaf today and added some color with some transtint dyes.
  22. Wish I could go. He is one demo I really want to...

    Wish I could go. He is one demo I really want to see. I love his work. Hopefully he will be in the chicago area some day.
  23. Replies
    14
    Views
    2,302

    Sorry Roger, that really sucks. Hopefully the...

    Sorry Roger, that really sucks. Hopefully the next one will work out better.
  24. I have a jet 1642. It is a very nice lathe. I...

    I have a jet 1642. It is a very nice lathe. I mainly make platers and the largest I can do is around 14", because I use jumbo jaws to turn the foot and you just do not have the room to open the jaws...
  25. Replies
    19
    Views
    2,445

    Looks good Bob. Did you wet sand with the micro...

    Looks good Bob. Did you wet sand with the micro mesh, and how high did you go with it?
Results 1 to 25 of 351
Page 1 of 15 1 2 3 4