Search:

Type: Posts; User: Jim Ritter; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.09 seconds.

  1. Thread: It Spins!

    by Jim Ritter
    Replies
    10
    Views
    608

    Sweet installation Marco, well done. Enjoy it....

    Sweet installation Marco, well done. Enjoy it.
    Jim
  2. Metal Lathes Can't help with info, but it looks like a nice...

    Can't help with info, but it looks like a nice little lathe.
    Jim
  3. I'm guessing you are not married? Jim

    I'm guessing you are not married?
    Jim
  4. Hi Richard of course right after I send you some...

    Hi Richard of course right after I send you some money you ask if I am selling them. No, I'm not selling them. They were the first things I made on my Benchmaster milling machine. I made parts enough...
  5. I made this one one for a swap and couldn't...

    I made this one one for a swap and couldn't decide on the cutter shape so I made a bunch of different ones.
    ...
  6. Replies
    7
    Views
    1,363

    Metal Lathes Any suggestions on disassembling the lathe for...

    Any suggestions on disassembling the lathe for transport? Do I have to cut the flat belt to remove the jack shaft and motor? I'm not sure where to start. The shaper is not following me home. It's...
  7. Replies
    6
    Views
    741

    I have more than a couple #3's and they are all...

    I have more than a couple #3's and they are all Stanley's and I did notice a couple months ago when I hung them up that some are different lengths. Not sure how much time I'll have to measure them...
  8. Replies
    17
    Views
    1,350

    That's a sweet sharpener Pete. I too am a...

    That's a sweet sharpener Pete. I too am a draftsman mostly in my former career, but still have my board set up and draw by hand. I would have bought that sharpener over a new one too.
    Jim
  9. Replies
    5
    Views
    437

    Yes Jim the inside edge of the radius is/was...

    Yes Jim the inside edge of the radius is/was sharpened. I'll try and take a better photo this evening.
    Jim
  10. Replies
    5
    Views
    437

    Yes it is like a scorp, cutting and hollowing on...

    Yes it is like a scorp, cutting and hollowing on the pull stroke. The handle is pinned on so it doesn't pull off. That is interesting about the prosthetics but this is much longer than would be...
  11. Replies
    5
    Views
    437

    Tool ID help needed

    I'm doing a basement clean out to help a neighbor dispose of her fathers tools and this was hanging on the wall. Curiosity has gotten the better of me on this one. I can find no makers marks. Here...
  12. Replies
    33
    Views
    3,134

    Here is a screen shot of Popular Mechanics Aug...

    Here is a screen shot of Popular Mechanics Aug 1930.

    http://i1135.photobucket.com/albums/m628/boatman53/8127cd144ae3c8785f3769c76f05410b_zpsf8512f60.jpg

    Jim
  13. Replies
    7
    Views
    1,363

    Metal Lathes Lathe and shaper

    I have an opportunity to upgrade my Atlas/Craftsman lathe to this Logan. Assuming everything works as it should would you do it?
    ...
  14. Replies
    5
    Views
    594

    I second Bills advise. Jim Edit: welcome to...

    I second Bills advise.
    Jim

    Edit: welcome to the Creek.
  15. Replies
    13
    Views
    1,294

    Those types of drawer inserts can be made in two...

    Those types of drawer inserts can be made in two pieces. The cutouts made with a fret or scroll saw then the bottom plywood is glued on. I'm working on one but I am using a small router bit for doing...
  16. Replies
    33
    Views
    3,134

    +1 not fond of it. With the knobs radiating like...

    +1 not fond of it. With the knobs radiating like that one is almost forced to put the screw lower than one might want. The last version I almost bought but not this one.
    Jim
  17. Replies
    12
    Views
    1,144

    I just did a search for "snow saw" and found many...

    I just did a search for "snow saw" and found many similar looking tools although none an exact match.
    Jim
  18. Replies
    12
    Views
    1,144

    I think Rob is the winner. Jim

    I think Rob is the winner.
    Jim
  19. Thread: Curiosity

    by Jim Ritter
    Replies
    18
    Views
    1,170

    Yes I use mine, I have several. I made an adapter...

    Yes I use mine, I have several. I made an adapter for using a 1/4" bit inserts. I use it with hex end drill bits to drill small holes also.
    Jim
  20. Replies
    5
    Views
    585

    I did some surveying also Stan. Almost made a...

    I did some surveying also Stan. Almost made a career out of it but started boatbuilding and there was no going back.
    Jim
  21. Replies
    5
    Views
    585

    Nice plumb bob! From what I know the steel points...

    Nice plumb bob! From what I know the steel points were used because the are more durable and replaceable. If the bob is dropped a brass point could get bent, then the bob is inaccurate.
    Jim
  22. Replies
    7
    Views
    678

    The chop on my leg vise is 6" and I have never...

    The chop on my leg vise is 6" and I have never needed more clamping area.
    Jim
  23. Replies
    9
    Views
    931

    Yup, clamps around an auger bit when used in a...

    Yup, clamps around an auger bit when used in a brace. It's a depth stop.
    Jim
  24. Replies
    9
    Views
    971

    The box alone is worth that from what I've seen,...

    The box alone is worth that from what I've seen, and it has the key. Make sure the key works with the lid open. Some keys can turn the tumblers to lock a box but do not line up to open it. I almost...
  25. Thread: Oh Shoot!

    by Jim Ritter
    Replies
    14
    Views
    1,675

    I miss my HP 41. It died years ago, damn salt...

    I miss my HP 41. It died years ago, damn salt air.
    Jim
Results 1 to 25 of 240
Page 1 of 10 1 2 3 4