Search:

Type: Posts; User: Richard Niemiec; Keyword(s):

Page 1 of 19 1 2 3 4

Search: Search took 0.02 seconds.

  1. Again, Ken, I'll not apologize for my...

    Again, Ken, I'll not apologize for my contributions to the forum, I give as much or more than I get. I'll also not apologize for my patronage of the advertisers in the banner ads; in fact, Rob Lee...
  2. Replies
    18
    Views
    3,514

    Once you get the rust off, get yourself some...

    Once you get the rust off, get yourself some camilla oil in the large spray bottle from Japan Woodworker, or where ever.... spray a small rag and give the tools a light coat when you put the plane...
  3. Aw, c'mon Ken, a little bit of a drive by there...

    Aw, c'mon Ken, a little bit of a drive by there .... "if you are really concerned about exchanging information." A review of my posts in the neader forum will show that I've given and shared what I...
  4. Replies
    14
    Views
    6,029

    Augusto: I've installed over $6000 of millwork...

    Augusto: I've installed over $6000 of millwork in my house, and I've found that using a coarser toothed coping saw blade is much better than the fine blades. Nothing special about the blade, Home...
  5. Glenn: Well, sites like this grow from user...

    Glenn: Well, sites like this grow from user generated content, ascribing membership growth to advertisers and user fees makes little sense to me; its the membership that shares their knowledge that...
  6. Well, a little bit of too many rules, and the...

    Well, a little bit of too many rules, and the slow erosion of access unless you pay, sort of grates on me from time to time. Seems like some folks have another agenda.
  7. Replies
    66
    Views
    14,960

    +1 George, you are right on target as far as...

    +1

    George, you are right on target as far as I'm concerned.
  8. Replies
    27
    Views
    3,594

    Like Frank Klausz, with a sharp pencil, and cut...

    Like Frank Klausz, with a sharp pencil, and cut on the line. Practice, practice....
  9. Replies
    7
    Views
    2,000

    They are out there at the flea markets, but...

    They are out there at the flea markets, but again, over priced; rustbuckets have asking prices of $15 each for under 1" sizes, those in better shape sometimes more. You got to be in the right place...
  10. Always start the cut on the push stroke; its a...

    Always start the cut on the push stroke; its a canard that you start on the pull. It takes a light touch and practice, but once you get the feel for it you'll never go back to the pull stroke.
  11. +1 ......but with a stone, not a...

    +1 ......but with a stone, not a file...........works for me.
  12. Replies
    19
    Views
    14,819

    Look for a Stanley or Millers Falls brace, make...

    Look for a Stanley or Millers Falls brace, make sure the ratcheting works, the chuck post is not worn out and the chuck operates smoothly. As long as the wood handles are in one piece, don't get too...
  13. Replies
    13
    Views
    2,751

    Doorstop. Or ballast under the lathe. Those...

    Doorstop.

    Or ballast under the lathe.

    Those are your choices. Seriously, don't waste your time on this one. Stanley "Handyman's" are superior to this plane, and I wouldn't recommend spending...
  14. The forked lever cap is not all that rare, so its...

    The forked lever cap is not all that rare, so its not particularly collectible. That being said, these make great users, so flatten the back of the iron and sharpen it up, it will serve you well.
  15. I'm sure IBC makes fine irons. What I don't...

    I'm sure IBC makes fine irons. What I don't understand is why folk expect not to have to sharpen a new iron a little bit, and flatten the back a little bit, on anybody's iron - notwithstanding any...
  16. Replies
    10
    Views
    2,395

    For $7 you should have bought it and made a tote,...

    For $7 you should have bought it and made a tote, if the sole and frog were in good shape and the iron had length. $7 in gas is what it takes to cut my lawn.....
  17. Replies
    15
    Views
    3,235

    Bandsaw, there's no shame in using one. Somebody...

    Bandsaw, there's no shame in using one. Somebody with a bandsaw close to the GA coast - help this guy out.....
  18. Replies
    6
    Views
    1,941

    You can get the handles at Diefenbacher tools: ...

    You can get the handles at Diefenbacher tools:

    http://www.diefenbacher.com/sale.htm
  19. Replies
    13
    Views
    2,368

    Frankly, a jack plane is generally used for...

    Frankly, a jack plane is generally used for rougher work, and the sole does not have to be perfectly flat. so long as the toe, the area immediately in front of and behind the mouth, and somewhere in...
  20. Replies
    19
    Views
    9,286

    A screw from the frog adjustment bracket of a...

    A screw from the frog adjustment bracket of a Stanley will do as a replacement in a pinch.
  21. Replies
    28
    Views
    4,605

    Larry, you might want to rethink, as the bed of a...

    Larry, you might want to rethink, as the bed of a 90 really does not lend itself to tenon trimming, not enough length to register properly. For another $10-15 or so, upgrade to a 92 or 93 if its not...
  22. Sharpening is the key skill to learn. A plane is...

    Sharpening is the key skill to learn. A plane is no more than a jig to hold an edge tool, in this case an iron. LV and LN make fine planes, I own more than a few, but for regular bench planes a...
  23. Scraper after planing if you need it. Depending...

    Scraper after planing if you need it. Depending on the stain/finish, raise the grain if really necessary with some spit coat shellac for sealing, or mineral spirits and then very lightly (I'll say...
  24. Replies
    28
    Views
    4,605

    If you're looking to go cheap, the standard angle...

    If you're looking to go cheap, the standard angle block plane of choice is a vintage Stanley 9 1/2; in good to excellent shape, they go for about $35 to $40 in the classifieds below, more often found...
  25. Replies
    29
    Views
    5,420

    Just to be clear, I don't have any problem with a...

    Just to be clear, I don't have any problem with a business plan that requires "members" to subscribe for content, Northwind owns the url, the servers, etc. and can do whatever it pleases. But the...
Results 1 to 25 of 475
Page 1 of 19 1 2 3 4