Search:

Angle Grinder with a wire brush....

I had a straight edge that was encrusted so much I couldnt read it at all... I zapped it with the grinder... bingo... looks like new...

It might gouge it a...

You would think that 3.5k would buy alot of packing materials..... dang... that is awful.... hopefully they take care of you...

Might I recommend a Grizzly... I hear they are good, and based on the Specs, they are more than addiquit.... http://www.grizzly.com/products/14-Extreme-Series-Bandsaw/G0555X

Or even for about...

Thats wonderful...

But yea... painkillers do wonders... a legal high... (I have had multiple surgeries myself(one oral surgery where the numbing agent wore off while the guy was stiching and...

I am a Novice...by far compared to some of these folks.. although I know my way around a shop...

I generally work on anything I need... and dont want particle board crap...

My shop is very...

Dang... talk about a different type of woodworking... I take it you didnt see him go in there with a set of chisels and a mallet... :D....

Well, I wish her a quick recovery.... I have a few...

Is this comment needed?

I did a small experiment on what I was using as a sliding table for my BS, mixing some stains together... the effect would be the same on Ply, right? Cuz thats what the sliding table is made out...

Only a few gouges.... I make sure only to run it quickly over, never hover....

But yea... I concur... if I felt like buying another tool, it would be a ROS for sure....

The stains I have, are...

I have a belt sander.... nice and quick :)

I previously stained it, now I cannot get the stain off the little lip.... so I think I will have to restain.... grr...

Ill post in a little while...

I hear helper blood cleans it out very well....

Second to that, Emery cloth, or have the helper pay to have it re-ground..... he wont do that again....

My question is, should I stain the desk that is just about finished(warmer weather has convinced me to finish her this evening...) Or should I just add a layer of poly? The desk is of pine, if that...

Oh contrare.... your pushing the block along causes friction.....

I have an Xacto right here... can squeeze all I want... no injuries...

Have any more half baked comments you would like to add?

Please dont go off half-cocked...... it only wastes my...

I could be wrong, but I think those create the friction, due to the weight, when it breaks the bone...(bone moves when broken, causing the friction.) But I could be wrong...

That is what I have been trying to state.... When a boat is heavier, its draft becomes greater(thus the displacement is greater...) Sorry If I wasnt clear on that one..

You can also squeeze a razor all you want, and not get cut... Inorder to be cut by something sharp, you friction must occur, such as rubbing your finger over the blade... :p

Ever see sword...

I always learned the shaving technique, to test a knife's sharpness..

I generally Ill try to shave either a knuckle, or a spot on my arm, to see if its sharp(I have a couple jack knives that I am...

I would say that you are a little of topic my fine feathered friend...

We were talking about boats such as yachts... last I checked no yacht is a barge....

And actually, draft is the major...

Same with the Angle Grinder... its works extremely well for the price.... although, it gets very hot(I can feel it through a Police issue, kevlar palmed glove(search gloves.... made so syringes...

You are right about that one Van.... no company ever gives you a free warranty.... ;)

http://fortwayne.craigslist.org/search/tls?query=jointer

Theres a few in your area... I would try a few of them, someone might still have it... there was a 4" for $75 and a Jet 6" for $350

To add a rule... Never buy anything that your income or life depends on:

Dont buy elevators
Carabinas
climbing stakes
Escalators
Cars
Children's Toys(most likely coated in lead paint)...

Ouch! I can see losing a finger... that they can easily mend... but losing a knuckle..... #$!~ that must have hurt...

I walk into things... I dont think I would ever trust myself near a spinning...

Ah yea.... very warm... it was about 95F last evening... I am glad I waxed the tools I just derusted... or I would have been very annoyed....