Search:

Lee Valley also has a story tape measure.

http://www.leevalley.com/en/wood/page.aspx?p=65359&cat=1,43513,65359

This actually started as an April Fools gag, but some took it as an actual product...

You may be able to adapt this door hinge.

http://www.leevalley.com/en/hardware/page.aspx?p=48629&cat=3,41305,55408&ap=1

Greg

Would the dust in the shop set off the smoke detector?

Greg

For shop counter tops 1/4 inch Hardboard , also called high-density fiberboard (HDF). This product is also known under Isorel or Masonite brand names.

Tack it down on your plywood or particle...

I have one made by Makita (paid a heck of a lot more than $59) always used it as a panel saw. Ran into a lot of flood restoration work and home owners wanted mahogany paneling replaced.

Using a...

I know this is not exactly what you are asking for but it might give you some ideas.

https://woodgears.ca/tool_holders/toolchest.html

Greg

Went to my local LV and got Shellwax cream, a wax based friction polish. A little expensive but great results. The wife likes the result so thats my standard. As far as expensive in retrospect a...

What is friction polish?

Greg

First time poster in Turners Forum new to turning. I've had a block of Padauk siting on a table for a couple of years. So yesterday it became a bowl, my shop is covered with this nasty red fine...

I think that the Shop Smith also has horizontal boreing capability.

Greg

Who needs free shipping the latest LV store, opened in Kingston ON a 15 minute drive.

This defiantly a gloat.

Greg

Matthis has a program for printing full size patterens. I've used this numerous times without problems. The program is $20.00 or so.

http://woodgears.ca/bigprint/

Greg

This is by far the easiest method I have found for cutting segments.

www.youtube.com/watch?v=E45244qX1PM

Greh

You are right the blades can be flipped. I chaged mine using the allen wrech supplied and the screws came out with no problem. It takes about 20 minutes to flip or change the blades.

Greg

Bruce could you please identify your ZCI and source of same.

Thanks

Greg

Kent have no direct experience with this product.

http://www.harborfreight.com/router-speed-control-43060.html

Greg

In the olden days when my father was abuilder he placed the baseboard on the subfloor. Because he dealt with a carpet inspect from DuPont. Who was called because of dark soiling around the edge of...

Steve: When I first read your post it appeared that youwere asking about dados. But as I read further began to wonder if you were asking about mortice and tenon.

Cutting dados in making a...

I stumbled across this video on band saw adjustments. Looked intersting even though it has a commercial bent.

https://www.youtube.com/watch?v=wGbZqWac0jU

Greg

There are a number of different methods to attach bed rails here are but a few.

http://www.leevalley.com/en/home/Search.aspx?action=n

Using these types of attachments can alleviate any...

The Bessey clamp extender requires the removal of one of the moveable heads so that there is a longer adjustable clamp.
...

Don't know how hard pallet nails are but have used this type of blade for demo work for years.
...

If this is going to be a frequently recurring process then this may be of interest.

http://www.leevalley.com/en/wood/page.aspx?p=32922&cat=1,42884

Greg

Rod.

Almonte is about a hour and a half drive. But more interesting is the new Lee Valley store opening in Kingston this fall, thats a fifteen minute drive.

Greg

What exactly is this device? Is it available or is it your creation?

Greg