Search:

heh, kind of odd huh.
They are cages for my reptiles.
The cages used to look like this;
http://i2.photobucket.com/albums/y2/nomad85/temps013.jpg
I thought they could use better accommodation, so...

Maybe I am wrong, but I would guess the majority of menards' customers are not "woodworkers", and may not have the means to refinish the wood, so anything with a smudge or mark from normal, or miss...

Sweet deal, I've been looking for a jointer also, would love to find a deal like that:D

Thanks for the comments everyone:) Makes me feel all warm and fuzzy...

I tried out my paste wax on this project, mainly because I needed to give it to her before her birthday was over... Only one...

I built this as a present for my sister on her birthday last week(maybe I should have built before the day of...)
Anyway it was my first try at a picture frame and it looked really good until I...

It's a Hunter, so is the remote unit.

Yea I read the instructions, and I understand most of the wiring.. just cant figure where to put the red wire... its got 2 black and 2 white, those are pretty easy... but the red wire...?

The fan does have a couple light bulbs, the ground is already figured out, so the screw is still a mystery, the screw is brass colored. I just don't know where to wire the red wire. The rest makes...

I need to but a remote control on a ceiling fan, the receiver has 5 wires, I can see that 4 are used to route the power, I just cant figure out where the red wire(says "light" on it) goes. There...

The jointer is already gone... But I might get the other saw... Might use it as an outfeed table for my saw, and get a stacked dado for it... I'll let you know what happens:)

I'll see how low he will go, I bet if I clean it up and dont like it I could sell it for no loss.
I also found this old saw... I don't need the saw, and I don't want the cabinet(puke)... but the...

Thanks guys, I'll keep looking:cool:

I was looking into a jointer after messing around with some crappy borg wood(it wasnt straight... now I see why everyone likes jointers) I found an older delta jointer locally for 100$OBO looks...

I agree that he ought to just make it tight, and not worry about, but he is very very detail oriented(he's an architect) and I don't think he will see it the same way. Thanks for all the replies I...

I doubt I'll ever use wood that thick(at least in the short term) I wouldn't even know where to find any.

What do the "plugs" look like? Is there a diagram I could look at to see where I need to apply oil?
Thanks

I was trying to setup some lighting in my little shop, my parents had a few unused 4' fluorescent fixtures. I picked up a bulk pack of bulbs and installed them. In each fixture only one bulb will...

Thats a really good idea, I think I will use something like that until I build a custom base/workstation for my saw. thank you for the pictures they help quite a bit.

Kyle

Whats a flange (that big washer?) I wouldn't know how to check that. It cuts really well, like a hot knife through butter:) Theres a nice pile of sawdust under the saw now. And I make a little push...

Thanks for the tip Matt

I picked up a big dust collector soon after I got the saw, but as of right now I don't have a way of hooking it up. Once I build the workstation and can implement a dust port into that, but the...

It was slow a few days ago for me, I tried other sites and they were normal speed, but that cant be avoided, seems fine now.

I finished rebuilding, squaring, aligning, and otherwise setting up my saw.
It's an old craftsman 113.298240. I took everything apart, cleaned it up and learned a lot in the process. I want to...

I tried that... much worse... and it ruined the paper

Thanks everyone, I love this site, all kinds of experience to go around.