Search:

Type: Posts; User: Ron Natalie; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    5,629

    Never seen any (and I own LOTS of harmonicas). ...

    Never seen any (and I own LOTS of harmonicas). You could take a manufactured harmonica and canabalize the reed plates and comb (you could make your own comb too I guess) and fit covers of your own...
  2. This is what happens when you deal with Chinese...

    This is what happens when you deal with Chinese manufacturers.
  3. Replies
    7
    Views
    2,165

    They have 1/2" rigid on the HD site. $14.48 for...

    They have 1/2" rigid on the HD site. $14.48 for a 10' length.
  4. Replies
    18
    Views
    3,901

    Hardwood? The classic wood for pencils is...

    Hardwood? The classic wood for pencils is Western Red Cedar.
  5. Replies
    12
    Views
    1,939

    I installed triangular shelf brackets around my...

    I installed triangular shelf brackets around my shop. The 6" DC piping goes thorugh the middle of the triangle. Gives me storage above...
  6. Replies
    16
    Views
    4,354

    I think you have one of the earlier ones. ...

    I think you have one of the earlier ones. Looking at some pictures, it looks like there were some that have a much wider slot for the riving knife (and it even routed out more of the melamine that...
  7. It might look like what they show in their...

    It might look like what they show in their patent: http://www.google.com/patents?id=nFmzAAAAEBAJ&pg=PA3&zoom=4&dq=MAGSWITCH+TECHNOLOGY+WORLDWIDE
  8. Replies
    16
    Views
    4,354

    They give you two inserts with the kit. One is...

    They give you two inserts with the kit. One is uncut, and the other has a kerf coming from the back to accomodate the riving knife. Your blade had better be wider than the knife anyhow, so the...
  9. I did all the stuff on my PCS with two other...

    I did all the stuff on my PCS with two other friends. As stated, when you unbox it, it has just the center section of the table on it. This makes it much narrower and somewhat lighter than the...
  10. The center section is attached, but as Joseph...

    The center section is attached, but as Joseph says, it the trunions are not attached to it. You can easily see this by just pulling out the blade insert and looking inside.
    Not attaching the...
  11. The PCS is shipped on a sort of styrofoam pallet...

    The PCS is shipped on a sort of styrofoam pallet without the extension wings and I just had the truck back up to the hangar and unload. Since I ordered the mobile kit I disregarded the silly...
  12. The 3 wire exception was removed in the 2008 NEC....

    The 3 wire exception was removed in the 2008 NEC. It would depend on what the effective date of the code in your area is.
  13. Usually it's the other way around. We put a...

    Usually it's the other way around. We put a vapor barrier down to keep the moisture from the soil OUT of the concrete. But it ought to work both ways.
  14. Where are you putting the other wire from your HF...

    Where are you putting the other wire from your HF meter?

    Is this an attached garage? Actually, in older versions of the code, you were allowed to run only three wires to an accessory building...
  15. Replies
    18
    Views
    3,962

    Perhaps not. I assumed that it was the same...

    Perhaps not. I assumed that it was the same gauge as the shorter pieces but I could be wrong. I have a grizzly 2HP cyclone. This longer piece doesn't have any intermediate crimps or beads in...
  16. Replies
    16
    Views
    4,354

    There's a guy selling Zero clearance inserts that...

    There's a guy selling Zero clearance inserts that are mostly hunks of aluminum with a hardboard insert that is replaceable in a sliding dovetail (they give you two inserts and you can buy more or...
  17. Replies
    19
    Views
    6,192

    It's easier to zero the DRO for a given operation...

    It's easier to zero the DRO for a given operation than to fix the reticle on the fence rail (or do the mental math to adjust for the fact that it's almost certainly OFF).
  18. Replies
    18
    Views
    3,962

    I have built my DC system with 26g snap duct. ...

    I have built my DC system with 26g snap duct. As with Ole, I used aluminum tape and the duct mastic to seal it up (which is a little easier).

    However, be careful. The short 2 foot lengths seem...
  19. Replies
    26
    Views
    5,964

    That looks like it will work or I might be...

    That looks like it will work or I might be inclined to try one of the griz switches: http://www.grizzly.com/products/220V-Paddle-On-Off-Switch/H8242
  20. At $50 you can hardly go wrong. You'd spend...

    At $50 you can hardly go wrong. You'd spend that trying to buy all the things to outfit the $17 HF one. I have no idea why the saw blades for these things are so darned expensive.
    I've got both...
  21. Replies
    26
    Views
    5,964

    That jointer appears to have a simple ON/OFF...

    That jointer appears to have a simple ON/OFF switch which I suspect only switches one pole of the power. There are two things that will trip a GFCI:
    1. An imbalance between the current going out...
  22. Replies
    22
    Views
    5,769

    I have a chain hoist on a trolley that rides the...

    I have a chain hoist on a trolley that rides the structural beam in my hangar. I just used the hoist hook and a some chain to stand up my Griz GO440 on it's stand.
  23. Either fill it with epoxy or other wood...

    Either fill it with epoxy or other wood stabilizer or cut out the rotted area and scab in a new piece. Either way it's going to be cheaper/nicer than replacing the door.
    Make sure any raw wood on...
  24. Replies
    8
    Views
    3,169

    I've got the JJP-12HH plugged into a 20A/240...

    I've got the JJP-12HH plugged into a 20A/240 circuit. I've not had any problems.
  25. Replies
    7
    Views
    19,939

    While I haven't done this particular minwax...

    While I haven't done this particular minwax product, I've used my HVLP gun with pretty good success thinning down and adding a touch of Penetrol.
    .
Results 1 to 25 of 309
Page 1 of 13 1 2 3 4