So based on that, are you still thinking that the wiring would be
green -> brown
blue -> red
red -> blue
Type: Posts; User: Mike Galea; Keyword(s):
So based on that, are you still thinking that the wiring would be
green -> brown
blue -> red
red -> blue
Update: Thank you all for the comments and advice. I did a search on the stepper motor (573S15-L), and found it along with the wiring diagram, wondering if anyone can decipher it for me. ...
A few weeks ago, my machine started having issues with the x axis movement. After some tech support from Ray (Rabbit Lasers, Great guy by the way), he told me to check the wires where they connect...
I received some info from Rabbit Laser on the z axis movement issues. They asked me the following info on the amplifier.....
As for the z axis, what is the amplifier set at inside your laser...
Thanks for the info. I have reached out to Ray, just waiting to hear back.
Thanks again
I will check that, and yes the table moves, not the head. Sorry I posted that earlier.
80 watt Hugo engraver from Hurricane Lasers
Lasercut 5.3
CorelDraw x5
Sorry about that, Here is the info on my machine...
As far as the z control, I have a button to adjust the z height, but when I hit it (which would normally move the head up and down) it just...
Ok, I have downloaded the new Lasercut software, and the LTUSB files (Carol at Rabbit instructed me to load these). I am now able to boot up the machine, but I am unsure where in Lasercut I can...
Update, I did speak with Carol at Rabbit (very friendly and helpful). I ordered the 6525, and received it today. It is a little larger than the 6515, and wont quite fit, but I think I can move...
Well I went with Rabbit Laser, they seem very knowledgeable, and I feel more comfortable paying a little more, but dealing with someone in the US. Board came to $635.00 with S&H.
I have literally spent hours upon hours checking every single connection in the system, and they all seem to be connected. After reading Dave's post on where the d1 light was located, I turned the...
Dave,
I tried to flash the firmware, followed the instructions, but does not even recognize the USB drive (the Drive is correctly formatted FAT16). I even tried to rule out the USB port and plug...
Thanks Tomas for your insight.
Thanks for the info. I will check them out.
I went home last night and could not find any loose wires to the control pad.
Thanks for the info.... I will try that tonight.
Thank you for the info.
I was looking to see if anyone could recommend a plasma cutting table (ideally something like a 4'x4'). My use would be for cutting metal signs and artwork . Material I would be cutting (primarily)...
I was wondering if anyone out there could possibly help me troubleshoot some issues with my Chinese laser engraver. I purchased an 80 watt engraver from Hurricane Lasers (which is no longer in...
Hello, I purchased a Chinese laser machine from Hurricane Lasers, about 2 1/2 years ago, and they have since went out of business. I have recently been having issues with my dongle for Lasercut,...
Dan,
I am not quite sure what you are saying !
I am looking for a good source of vector files. I have seen several sources that charge a monthly fee (which is fine by me) as long as they are quality vector files. Any help would be greatly...
I was wondering if anyone had any feedback good/bad on the Laser University through Laserbits. I am new to Laser Engraving and it looks to offer a lot of tutorials and info on all sorts of different...
I just purchased my first laser (a Chinese machine 80watt) which runs Lasercut5 along with Corelx5. I would like to start lasering photos onto different materials such as wood, anondized aluminum,...
Anyone out there running a Hurricane Laser engraver ? Spoke with a rep there and he is going to take my design and send me some samples of what his machines can produce. I just worry because I hear...