The legs are 1 1/2" to start and then after sanding and finish they are at about 1 3/16"
I can send you what plans I have if you want them, send me an email to wlhuber@att.net
Type: Posts; User: Bill Huber; Keyword(s):
The legs are 1 1/2" to start and then after sanding and finish they are at about 1 3/16"
I can send you what plans I have if you want them, send me an email to wlhuber@att.net
I would really think hard on that sander, the head does not move just the table, this is fine for small parts but for longer one it is a problem. You would have to made and adjustable infeed out feed...
I was using a 6HP Ridgid vac and it was just enough, but if I was sanding a board that was say 8" wide it would get some dust in the air. There is no question that a good DC would be better but if...
It is really bad and what gets me is the fact that he walks out with a little over 2 million dollars to support his habit with.
I used a cheap scroll sawn.
It is has been a long while but I am still here, just a bunch of different things going on in my life right now.
It has been raining so much here in Texas I thought I had better build me an ark......
I just get the brass rod at Ace Hardware I am sure the are many places to get brass rod.
I have had the Ridgid, Bosch and now the Dewalt.
The Ridgid, I got it and within an hour I took it back and exchanged it for a new one. It got so hot I could not hold it. Took the new one home and...
I had that same problem at one time with one of the planners.
First the wrench that comes with the planner is junk and you need to get a good one.
When I had the problem I ordered new screws...
I am not sure why they put it that far in front of the bit. I have the Jessem 24x32 table and the rails are set 3" in front of the center. The only time I could see moving the fence in front of...
Go download MalwareBytes and run it, make sure you up date the data file to the latest one.
https://www.malwarebytes.org/mwb-download/
My wife had the same problem on her PC and we found a...
I have one on my old Craftsman and it works ok, I don't use it to be real accurate, I use it to get close and then I have a punch mark to put the drill bit into.
Now if you really want to drill a...
I use an upcut in the router table but I will have to say I am using the table saw a lot more now.
I have the same ones that Roger showed, they are great and you can use one hand to hold the strap in place and the other hand to tighten the straps.
Well I guess that picture is kind of like a TV ad....
That picture was taken when I first made the chair, it is now nice and gray.
I have not use a lot of redwood but I did make a nice Adirondak chairs about 8 years ago and it is still going, never been put inside, has set out all that time.
317999
There are a lot of good routers out there and I guess unless you have tried them all it is hard to say which is best.
I started out with a Bosch 1617 EVS kit and it has really done a great job for...
I never screw the rods into the jig myself, I do just like Mreze, put them in the block and push the jig against them.
This works just fine and I have never had a problem the the hole not being spot...
I just have a 10-20 sander and have done some 18 inch panels with it and it works out fine, you do have to have good support on the in-feed, out-feed and sides to get it done right.
With that...
I agree with Prashun, the inserts are the only real difference and the color.
I like the plastic inserts, I can make zero clearance inserts with them, put a bit in with the lift all the way down...
It doesn't have to move on both sides, when you lock one end down and then adjust the other end with the micro adjuster it will move the fence in or out as you need it to.
We are talking about micro...
I have the same lift, table, slider and fence, what a great setup.
Here is what I made for the table and it works very well, I leave one on the table most of the time, I have found that I don't...
I have the Jessem Master R Left II and love it.
Everything is done above the table, when I got it I had a Bosch 1617 in it and now have changed it out for the PC 7518 and the lift handles it just...
I think all the Ridgid stuff was gray and then they changed it to the orange some years ago.
I have one and it gets used all the time, I use the belt more then the spindle but that is just the...
What do you do to keep the batteries from corroding in flashlights and things like that, that you don't use a lot.
I have a good head light that uses 4 AA batteries and when I went to use it the...