Search:

With about 3-4” left of the board it seems to get stuck and needs a good nudge. I’ll run some test pieces and shut it off at that moment and see maybe what the issue is; pressure bar or rear roller....

Fed fine with the original blades and even the replacement straight blades. I’ll give the bed a better polish and wax and see if that helps too. I think it’s the read roller that needs adjusting.

I finally upgraded the cutterhead on this 16” 5hp powermatic. I’ve had the cutterhead for over a year and worried about the complexity of the install. Wasn’t that hard actually with the right tools. ...

Don't have room for a bench garage like that. Not sure I'll be hammering down either. More to utilize the end of the saw, keep pieces stationery during sanding, drilling etc.

I really want to make this. My space is limited and I often use my table saw as a work space. This vise will work great for clamping BUT also limited.

I thought about adding two dog holes in the...

I bought a used Sawstop and used Italian laguna. Both have lots of cast iron. My Sawstop I use as a glue table and it got bad. I scraped off the glue and used a burgundy scotch pad. Smooth like glass...

I have an older handmedown 12” ridgid. I’ve noticed blade wobble. It also doesn’t have a guard, shroud or clamps.

I’ve been looking at the Bosch Glide 12” for $599 currently. The Makita LS1219L...

Hey John, yeah, it's sapele and I think paduak, not really sure on the center strip. It was in my pile. I wanted a 13" piece of 8/4 sapele that was 12ft long so I could do my first mitered waterfall...

I have a set of cheap sawhorses from HD that need to go. I was eyeballing the Toughbuilt c700 saw horses. I like the idea of dropping a piece of ply or foam to use a support for my track saw.

I...

I’ve got 3 or coats on top and middle shelf and 6 coats on the vertical sides.

How do I apply the last coat? Been using a sponge pad. I’ve been sanding lightly with 400 between coats.

Will...

I’m actually ok in my garage without heat BUT just read the label on Arm R Seal and it suggested 70 degrees or higher.

I’m Norcal Bay Area and my garage will be 50s to 60s for the next 3-4 months...

Albert What bit? I just tried making a through tenon/domino for an 8mm cutter. I used I think a 1/4” roudover. It worked ok, not as perfect fit in the radius of a 8mm mortise as I’d like.
...

My first go using a domino 700 and making a mitered edge table.

It’s sapele and I think paduak strip.

I’m leaning toward Arm a Seal satin for ease of application and quickness in drying....

I was in your boat with an older 5hp 3 phase planer. I initially tried a cheap Huang (spelling) VFD. At the time it was the only VFD that could take 220 in and convert it to power a 5hp motor. Only...

Only 1/2” roughly with 700 and the seneca adapter? It doesn’t seem deep enough for a lot of applications.

I just picked up a barely used Domino 700. I want to get the Seneca small bit adapter.

Does the adapter change how deep mortises can be plunged? From reviews everyone seems to love the adapter.

My plans for a waterfall (mitered) edge went south. I couldn’t joint the 12ft board in order to get be a 70” top and two 26” legs.

Plan B: I still want to do a mitered joint.

I need to...

$7.50-$9/bf for 8/4 sapele. Didn’t think that was bad. $200 roughly in lumber. Maybe another $75 if I decide to run a 70” shelf.

I’m hoping I can get a 5 month old domino 700 574447 for $1k. Seller asking $1300 and an hour drive away.

Seller didn’t register it for warranty. I might be able to with all of sellers info. I...

Wife wants a console table for behind sofa. Be 10-12” wide and Between 60-70” long.

I immediately thought of using Sapele and doing a waterfall edge. Give me an excuse to cut a 45 with my...

I want a CNC but don't have the space. It then hit me, what about building a CNC and then hoisting it to the ceiling when not in use?
I want to flatten odd shaped slabs and endgrain boards. Cut...

I dove into the Makita 18v deep end once my hand me down 14v couldn’t hang.

I got the brushless oscillating tool and it’s great. Trim base board, cut nails in fences posts, 45 wood to fit inside...

What about Festool and other track clamps working in dovetail slots? I guess I can try with a dovetail bit I should have.

I'm debating on getting some these clamps for fence jigs, tapering jigs, add slots to my crosscut sled, and probably add slots to my outfeed table.

After doing some research there are two kids...

I've been lusting after a larger planer for awhile. I made the decision last April to keep my 16" 5hp probably 50 year old powermatic planer and upgrade it to a Byrd spiral cutterhead. Well the...